参数资料
型号: LTC3867EUF#PBF
厂商: Linear Technology
文件页数: 24/36页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM CM 24-QFN
产品培训模块: LTC3867 Synchronous Step-Down DC/DC Controller
标准包装: 91
PWM 型: 电流模式
输出数: 1
频率 - 最大: 1.2MHz
占空比: 98%
电源电压: 4 V ~ 38 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 125°C
封装/外壳: 24-WFQFN 裸露焊盘
包装: 管件
LTC3867
APPLICATIONS INFORMATION
V FB = V REF –
t SOFTSTART = 0.6 ?
SP series of surface mount special polymer capacitors
available in case heights ranging from 2mm to 4mm. Other
capacitor types include Sanyo POSCAP, Sanyo OS-CON,
Nichicon PL series and Sprague 595D series. Consult the
manufacturers for other specific recommendations.
Differential Amplifier
The LTC3867 has true remote voltage sense capability.
The sensing connections should be returned from the
load, back to the differential amplifier’s inputs through a
common, tightly coupled pair of PC traces. The differential
amplifier rejects common mode signals capacitively or
inductively radiated into the feedback PC traces as well
as ground loop disturbances. The LTC3867 diffamp has
high input impedance on DIFF + . It is designed to be used
with a feedback divider Kelvined to the load. The output
of the diffamp connects to the V FB pin.
Nonlinear Control Loop
The LTC3867 features a unique control loop that can speed
up transient response dramatically. This feature is enabled
and programmed through the IFAST pin. When IFAST is
tied to INTV CC , the nonlinear control loop is disabled. V IFAST
is the voltage that can be programmed on the IFAST pin.
There is a precision 10μA flowing out of the IFAST pin.
Connecting a resistor to SGND sets the V IFAST voltage.
When V IFAST is set below 1.4V, the difference of 1.4V and
V IFAST sets the threshold voltage that triggers nonlinear
control. Nonlinear control is only enabled when V FB is
within the UV and OV window. It should be enabled only
for forced continuous mode of operation.
Once nonlinear control is enabled, the top gate of all chan-
nels will turn on if:
1.4 – V IFAST
12.5
where V REF is the reference voltage, normally at 0.6V, and
V FB is the feedback voltage.
External Soft-Start and Tracking
The LTC3867 has the ability to either soft-start by itself
or track the output of another channel or external supply.
When the controller is configured to soft-start by itself, a
capacitor may be connected to its TK/SS pin or the internal
soft-start may be used. The controller is in the shutdown
state if its RUN pin voltage is below 1.22V and its TK/SS
pin is actively pulled to ground in this shutdown state. If
the RUN pin voltage is above 1.22V, the controller powers
up. A soft-start current of 1.25μA then starts to charge the
TK/SS soft-start capacitor. Note that soft-start or tracking
is achieved not by limiting the maximum output current
of the controller but by controlling the output ramp volt-
age according to the ramp rate on the TK/SS pin. Current
foldback is disabled during this phase to ensure smooth
soft-start or tracking. The soft-start or tracking range is
defined to be the voltage range from 0V to 0.6V on the
TK/SS pin. The total soft-start time can be calculated as:
C SS
1.25μA
Regardless of the mode selected by the MODE pin, the
controller always starts in discontinuous mode up to
TK/SS = 0.5V. Between TK/SS = 0.5V and 0.565V, it will
operate in forced continuous mode and revert to the
selected mode once TK/SS > 0.565V. The output ripple
is minimized during the 65mV forced continuous mode
window ensuring a clean PGOOD signal. When the chan-
nel is configured to track another supply, the feedback
voltage of the other supply is duplicated by a resistor
divider and applied to the TK/SS pin. Therefore, the volt-
age ramp rate on this pin is determined by the ramp rate
of the other supply’s voltage. It is only possible to track
another supply that is slower than the internal soft-start
ramp. Note that the small soft-start capacitor charging
current is always flowing, producing a small offset error.
To minimize this error, select the tracking resistive divider
value to be small enough to make this error negligible.
In order to track down another channel or supply after
3867f
24
相关PDF资料
PDF描述
LTC3868EUFD-1#PBF IC REG CTRLR BUCK PWM CM 28-QFN
LTC3869EUFD#PBF IC REG CTRLR BUCK PWM CM 28-QFN
LTC3872ETS8#TRMPBF IC REG CTRLR BST PWM CM TSOT23-8
LTC3873EDDB#TRMPBF IC REG CTRLR BST FLYBK PWM 8-DFN
LTC3873ITS8-5#TRPBF IC REG CTRLR BST FLYBK TSOT23-8
相关代理商/技术参数
参数描述
LTC3867IUF#PBF 功能描述:IC REG CTRLR BUCK PWM CM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3867IUF#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3868EGN-1#PBF 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3868EGN-1#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3868EUFD-1#PBF 功能描述:IC REG CTRLR BUCK PWM CM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR