- 您现在的位置：买卖IC网 > PDF目录1833 > LTC3869EUFD#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 28-QFN PDF资料下载
参数资料
| 型号： | LTC3869EUFD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/42页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-QFN |
| 标准包装： | 73 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 850kHz |
| 占空比： | 95% |
| 电源电压： | 4 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
LTC3869/LTC3869-2
APPLICATIONS INFORMATION
R SENSE(EQUIV)
DCR (MAX) at T L(MAX)
R1|| R2 =
ToscalethemaximuminductorDCRtothedesiredsense
resistor value, use the divider ratio:
R D =
C1 is usually selected to be in the range of 0.047μF to
0.47μF. This forces R1|| R2 to around 2k?, reducing er-
ror that might have been caused by the SENSE pins’ ±1μA
current. T L(MAX) is the maximum inductor temperature.
The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
L
(DCR at 20 ° C) ? C1
The sense resistor values are:
Slope Compensation and Inductor Peak Current
Slope compensation provides stability in constant-
frequency architectures by preventing subharmonic oscil-
lations at high duty cycles. It is accomplished internally by
adding a compensating ramp to the inductor current signal
at duty cycles in excess of 40%. Normally, this results in
a reduction of maximum inductor peak current for duty
cycles > 40%. However, the LTC3869 uses a scheme that
counteracts this compensating ramp, which allows the
maximum inductor peak current to remain unaffected
throughout all duty cycles.
Inductor Value Calculation
Given the desired input and output voltages, the inductor
value and operating frequency f OSC directly determine the
inductor’s peak-to-peak ripple current:
V OUT ? V IN – V OUT ?
V IN ? f OSC ? L ?
R1 =
R1|| R2
R D
; R2 =
R1 ? R D
1 ? R D
I RIPPLE =
? ?
( V IN(MAX) ? V OUT ) ? V OUT
P LOSS R1 =
V IN – V OUT V
ThemaximumpowerlossinR1isrelatedtodutycycle,
and will occur in continuous mode at the maximum input
voltage:
R1
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor,
due to the extra switching losses incurred through R1.
However, DCR sensing eliminates a sense resistor, reduces
conduction losses and provides higher efficiency at heavy
loads. Peak efficiency is about the same with either method.
To maintain a good signal to noise ratio for the current
sense signal, use a minimum ?V SENSE of 10mV for duty
cycles less than 40%. For a DCR sensing application, the
actual ripple voltage will be determined by the equation:
Lower ripple current reduces core losses in the inductor,
ESR losses in the output capacitors, and output voltage
ripple. Thus, highest efficiency operation is obtained at
low frequency with a small ripple current. Achieving this,
however, requires a large inductor.
A reasonable starting point is to choose a ripple current
that is about 40% of I OUT(MAX) for a duty cycle less than
40%. Note that the largest ripple current occurs at the
highest input voltage. To guarantee that ripple current does
not exceed a specified maximum, the inductor should be
chosen according to:
L ≥ ? OUT
f OSC ? I RIPPLE V IN
For duty cycles greater than 40%, the 10mV current
sense ripple voltage requirement is relaxed because the
slope compensation signal aids the signal-to-noise ratio
and because a lower limit is placed on the inductor value
to avoid subharmonic oscillations. To ensure stability for
?V SENSE =
V IN ? V OUT V OUT
R1 ? C1 V IN ? f OSC
38692fa
For more information www.linear.com/LTC3869
17
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3872ETS8#TRMPBF | IC REG CTRLR BST PWM CM TSOT23-8 |
| LTC3873EDDB#TRMPBF | IC REG CTRLR BST FLYBK PWM 8-DFN |
| LTC3873ITS8-5#TRPBF | IC REG CTRLR BST FLYBK TSOT23-8 |
| LTC3876EFE#PBF | IC CTLR DC/DC DDR DUAL 38-TSSOP |
| LTC3878EGN#PBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3869IGN-2#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3869IGN-2#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3869IUFD#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LTC3869IUFD#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3872EDDB#PBF | 制造商:Linear Technology 功能描述:DC DC Cntrlr Single-OUT Step Up 2.75V to 9.8V Input 8-Pin DFN EP 制造商:Linear Technology 功能描述:BOOST 2.75 - 9.8V 550KHZ 8D 制造商:Linear Technology 功能描述:BOOST, 2.75 - 9.8V, 550KHZ, 8DFN |
发布紧急采购，3分钟左右您将得到回复。