参数资料
型号: LTC3890EGN-1#PBF
厂商: LINEAR TECHNOLOGY CORP
元件分类: 稳压器
英文描述: SWITCHING CONTROLLER, PDSO28
封装: LEAD FREE, PLASTIC, SSOP-28
文件页数: 17/36页
文件大小: 498K
代理商: LTC3890EGN-1#PBF
LTC3890-1
24
38901f
APPLICATIONS INFORMATION
The minimum on-time for the LTC3890-1 is approximately
90ns. However, as the peak sense voltage decreases the
minimum on-time gradually increases up to about TBDns.
This is of particular concern in forced continuous applica-
tions with low ripple current at light loads. If the duty cycle
drops below the minimum on-time limit in this situation,
a signicant amount of cycle skipping can occur with
correspondingly larger current and voltage ripple.
Efciency Considerations
The percent efciency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efciency and which change would
produce the most improvement. Percent efciency can
be expressed as:
%Efciency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percent-
age of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC3890-1 circuits: 1) IC VIN current, 2) INTVCC
regulator current, 3) I2R losses, 4) topside MOSFET
transition losses.
1. The VIN current is the DC supply current given in the
Electrical Characteristics table, which excludes MOSFET
driver and control currents. VIN current typically results
in a small (<0.1%) loss.
2. INTVCC current is the sum of the MOSFET driver and
control currents. The MOSFET driver current results
from switching the gate capacitance of the power
MOSFETs. Each time a MOSFET gate is switched from
low to high to low again, a packet of charge, dQ, moves
from INTVCC to ground. The resulting dQ/dt is a current
out of INTVCC that is typically much larger than the
control circuit current. In continuous mode, IGATECHG
= f(QT + QB), where QT and QB are the gate charges of
the topside and bottom side MOSFETs.
Supplying INTVCCfromanoutput-derivedsourcepower
through EXTVCC will scale the VIN current required
for the driver and control circuits by a factor of (Duty
Cycle)/(Efciency). For example, in a 20V to 5V applica-
tion, 10mA of INTVCC current results in approximately
2.5mA of VIN current. This reduces the midcurrent loss
from 10% or more (if the driver was powered directly
from VIN) to only a few percent.
3. I2R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resis-
tor, and input and output capacitor ESR. In continuous
mode the average output current ows through L and
RSENSE, but is chopped between the topside MOSFET
and the synchronous MOSFET. If the two MOSFETs
have approximately the same RDS(ON), then the resis-
tance of one MOSFET can simply be summed with the
resistances of L, RSENSE and ESR to obtain I2R losses.
For example, if each RDS(ON) = 30mΩ, RL = 50mΩ,
RSENSE = 10mΩ and RESR = 40mΩ (sum of both input
and output capacitance losses), then the total resistance
is 130mΩ. This results in losses ranging from 3% to
13% as the output current increases from 1A to 5A for
a 5V output, or a 4% to 20% loss for a 3.3V output.
Efciency varies as the inverse square of VOUT for the
same external components and output power level. The
combined effects of increasingly lower output voltages
and higher currents required by high performance digital
systems is not doubling but quadrupling the importance
of loss terms in the switching regulator system!
4. Transition losses apply only to the topside MOSFET(s),
and become signicant only when operating at high
input voltages (typically 15V or greater). Transition
losses can be estimated from:
Transition Loss = (1.7) VIN 2 IO(MAX) CRSS f
Other hidden losses such as copper trace and internal
battery resistances can account for an additional 5%
to 10% efciency degradation in portable systems. It
is very important to include these system level losses
相关PDF资料
PDF描述
LTC3890IGN-1#TRPBF SWITCHING CONTROLLER, PDSO28
LTC3890IGN-1#PBF SWITCHING CONTROLLER, PDSO28
LTC3890MPUH#TRPBF DUAL SWITCHING CONTROLLER, 585 kHz SWITCHING FREQ-MAX, PQCC32
LTC3890EUH#PBF DUAL SWITCHING CONTROLLER, 585 kHz SWITCHING FREQ-MAX, PQCC32
LTC3890IUH#TRPBF DUAL SWITCHING CONTROLLER, 585 kHz SWITCHING FREQ-MAX, PQCC32
相关代理商/技术参数
参数描述
LTC3890EGN-3#PBF 制造商:Linear Technology 功能描述:IC REG CTRLR BUCK PWM CM 28SSOP 制造商:Linear Technology 功能描述:DC-DC CONTROLLER BUCK 900KHZ 制造商:Linear Technology 功能描述:DC-DC CONTROLLER, BUCK, 900KHZ, SSOP-28 制造商:Linear Technology 功能描述:DC-DC CONTROLLER, BUCK, 900KHZ, SSOP-28; Primary Input Voltage:60V; No. of Outputs:2; No. of Pins:28; Operating Temperature Min:-40C; Operating Temperature Max:125C; Operating Temperature Range:-40C to +125C ;RoHS Compliant: Yes
LTC3890EGN-3#TRPBF 制造商:Linear Technology 功能描述:IC REG CTRLR BUCK PWM CM 28SSOP
LTC3890EUH#PBF 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR
LTC3890EUH#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3890EUH-2#PBF 制造商:Linear Technology 功能描述:DC DC Cntrlr Dual-OUT Sync Step Down 4V to 60V Input 32-Pin QFN EP 制造商:Linear Technology 功能描述:DP-SWREG/Controller, 60V, Low IQ, Dual Output Synchronous Step-Down Controller