- 您现在的位置：买卖IC网 > PDF目录16300 > LTC4000EGN#PBF (Linear Technology)IC CHARGER BATTERY 28-SSOP PDF资料下载
参数资料
| 型号： | LTC4000EGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/40页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY 28-SSOP |
| 产品培训模块： | LTC4000 60V Battery Charging Controller and Power Management |
| 标准包装： | 49 |
| 系列： | PowerPath™ |
| 功能： | 充电管理，电源管理 |
| 电池化学： | 多化学 |
| 电源电压： | 3 V ~ 60 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC4000
APPLICATIONS INFORMATION
R CS =
? I CLIM = CL ? 2.5μA
R CL =
R BFB1 = ? FLOAT – 1 ? R BFB2
V FLOAT = ? BFB1
? 1.136V ? – ? BFB1 ? V FBG ?
I CLIM(MAX) (A) =
R CL =
? I CLIM(TRKL) = 0.25μA ?
I CLIM(TRKL) =
ThevoltageontheIIMONpincanbefilteredfurtherbyputting
a capacitor on the pin (C IIMON ). The voltage on the IIMON
pin is also the feedback input to the input current regulation
error amplifier. Any capacitor connected to this pin places
a pole in the input current regulation loop. Therefore, this
filter capacitor should NOT be arbitrarily large as it will slow
down the overall compensated loop. For details on loop
compensation please refer to the Compensation section.
Charge Current Limit Setting and Monitoring
The regulated full charge current is set according to the
following formula:
V CL
20 ? I CLIM
where V CL is the voltage on the CL pin. The CL pin is
internally pulled up with an accurate current source of
50μA. Therefore, an equivalent formula to obtain the input
current limit is:
I CLIM ? R CS R
2.5μA R CS
The charge current through the sense resistor is available
for monitoring through the IBMON pin. The voltage on
the IBMON pin varies with the current through the sense
resistor as follows:
V IBMON = 20 ? I RCS ? R CS = 20 ? ( V CSP – V CSN )
Similar to the IIMON pin, the regulation voltage level at
the IBMON pin is clamped at 1V with an accurate internal
reference. At 1V on the IBMON pin, the charge current
limit is regulated to the following value:
0.050V
R CS ( ? )
When this maximum charge current limit is desired, leave
the CL pin open or set it to a voltage >1.05V such that
amplifier A5 can regulate the IBMON pin voltage accurately
to the internal reference of 1V.
When the output current waveform of the DC/DC converter
or the system load current is noisy, it is recommended that
a capacitor is connected to the CSP pin (C CSP ). This is to
reduce the AC content of the current through the sense
resistor (R CS ). Where the highest accuracy is important,
pick the value of C CSP such that the AC content is less
than or equal to 50% of the average voltage across the
sense resistor. Similar to the IIMON pin, the voltage on the
IBMON pin is filtered further by putting a capacitor on the
pin (C IBMON ). This filter capacitor should not be arbitrarily
large as it will slow down the overall compensated charge
current regulation loop. For details on the loop compensa-
tion, refer to the Compensation section.
Battery Float Voltage Programming
When the value of R BFB1 is much larger than 100Ω, the final
float voltage is determined using the following formula:
? V ?
? 1.136V ?
When higher accuracy is important, a slightly more ac-
curate final float voltage can be determined using the
following formula:
? R + R BFB2 ? ? R ?
? R BFB2 ? ? R BFB2 ?
where V FBG is the voltage at the FBG pin during float
voltage regulation, which accounts for all the current
from all resistor dividers that are connected to this pin
(R FBG = 100Ω typical).
Low Battery Trickle Charge Programming and Bad
Battery Detection
When charging into an over-discharged or dead battery
(V BFB < V LOBAT ), the pull-up current at the CL pin is reduced
to 10% of the normal pull-up current. Therefore, the trickle
charge current is set using the following formula:
I CLIM(TRKL) ? R CS R CL
0.25μA R CS
Therefore, when 50μA ? R CL is less than 1V, the following
relation is true:
I CLIM
10
4000fb
For more information www.linear.com/LTC4000
17
相关PDF资料 |
PDF描述 |
|---|---|
| EBC22DRES-S734 | CONN EDGECARD 44POS .100 EYELET |
| EET-ED2G221DA | CAP ALUM 220UF 400V 20% SNAP |
| ESC06DRAS-S734 | CONN EDGECARD 12POS .100 R/A PCB |
| RCM12DCST | CONN EDGECARD 24POS DIP .156 SLD |
| EMC05DRAN-S734 | CONN EDGECARD 10POS .100 R/A PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4000EUFD#PBF | 功能描述:IC CHARGER BATTERY 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000EUFD#TRPBF | 功能描述:IC CHARGER BATTERY 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000EUFD-1#PBF | 功能描述:IC BATT CHRGR MULTI-CHEM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC4000EUFD-1#TRPBF | 功能描述:IC CHARGE MGMT MULTI CHEM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000IGN#PBF | 功能描述:IC CHARGER BATTERY 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。