- 您现在的位置：买卖IC网 > PDF目录16300 > LTC4000EGN#PBF (Linear Technology)IC CHARGER BATTERY 28-SSOP PDF资料下载
参数资料
| 型号： | LTC4000EGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/40页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY 28-SSOP |
| 产品培训模块： | LTC4000 60V Battery Charging Controller and Power Management |
| 标准包装： | 49 |
| 系列： | PowerPath™ |
| 功能： | 充电管理，电源管理 |
| 电池化学： | 多化学 |
| 电源电压： | 3 V ~ 60 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC4000
PIN FUNCTIONS
(QFN/SSOP)
I CLIM = 2.5μA ? ? CL ?
V FLOAT =
R BFB2 + R BFB1
is not exceeded. The charge current limit is determined
using the following formula:
? R ?
? R CS ?
Where R CS is the sense resistor connected to the CSP
and the CSN pins. Leave the pin open for the maximum
charge current limit of 50mV/R CS .
TMR (Pin 9/Pin 5): Charge Timer. Attach 1nF of external
capacitance (C TMR ) to GND for each 104 seconds of charge
termination time and 26 seconds of bad battery indicator
time. Short to GND to prevent bad battery indicator time
and charge termination time from expiring – allowing a
continuous trickle charge and top off float voltage regula-
tion charge. Short to BIAS to disable bad battery detect
and enable C/X charging termination.
GND (Pins 10, 28, 29/Pins 6, 24): Device Ground Pins.
Connect the ground pins to a suitable PCB copper ground
plane for proper electrical operation. The QFN package
exposed pad must be soldered to PCB ground for rated
thermal performance.
FLT , CHRG (Pin 11, Pin 12/Pin 7, Pin 8): Charge Status
Indicator Pins. These pins are high voltage open drain pull
down pins. The FLT pin pulls down when there is an under
or over temperature condition during charging or when
the voltage on the BFB pin stays below the low battery
threshold during charging for a period longer than the bad
battery indicator time. The CHRG pin pulls down during
a charging cycle. Please refer to the application informa-
tion section for details on specific modes indicated by the
combination of the states of these two pins. Pull up each
of these pins with an LED in series with a resistor to a
voltage source to provide a visual status indicator. Short
these pins to GND when not used.
BIAS (Pin 13/Pin 9): 2.9V Regulator Output. Connect a
capacitor of at least 470nF to bypass this 2.9V regulated
voltage output. Use this pin to bias the resistor divider to
set up the voltage at the NTC pin.
NTC (Pin 14/Pin 10): Thermistor Input. Connect a ther-
mistor from NTC to GND, and a corresponding resistor
from BIAS to NTC. The voltage level on this pin determines
if the battery temperature is safe for charging. The charge
current and charge timer are suspended if the thermistor
indicates a temperature that is unsafe for charging. Once the
temperature returns to the safe region, charging resumes.
Leave the pin open or connected to a capacitor to disable
the temperature qualified charging function.
FBG (Pin 15/Pin 11): Feedback Ground Pin. This is the
ground return pin for the resistor dividers connected to
the BFB and OFB pins. As soon as the voltage at IN is valid
(>3V typical), this pin has a 100Ω resistance to GND. When
the voltage at IN is not valid, this pin is disconnected from
GND to ensure that the resistor dividers connected to the
BFB and OFB pins do not continue to drain the battery
when the battery is the only available power source.
BFB (Pin 16/Pin 12): Battery Feedback Voltage Pin. This
pin is a high impedance input pin used to sense the battery
voltage level. In regulation, the battery float voltage loop
sets the voltage on this pin to 1.136V (typical). Connect
this pin to the center node of a resistor divider between
the BAT pin and the FBG pin to set the battery float voltage.
The battery float voltage can then be obtained as follows:
? 1.136V
R BFB2
BAT (Pin 17/Pin 13): Battery Pack Connection. Connect
the battery to this pin. This pin is the anode of the battery
ideal diode driver (the cathode is the CSN pin).
BGATE (Pin 18/Pin 14): External Battery PMOS Gate Drive
Output. When not charging, the BGATE pin drives the
external PMOS to behave as an ideal diode from the BAT
pin (anode) to the CSN pin (cathode). This allows efficient
delivery of any required additional power from the battery
to the downstream system connected to the CSN pin.
When charging a heavily discharged battery, the BGATE
pin is regulated to set the output feedback voltage (OFB
pin) to 86% of the battery float voltage (0.974V typical).
This allows the instant-on feature, providing an immedi-
ate valid voltage level at the output when the LTC4000 is
charging a heavily discharged battery. Once the voltage
on the OFB pin is above the 0.974V typical value, then the
BGATE pin is driven low to ensure an efficient charging
path from the CSN pin to the BAT pin.
4000fb
For more information www.linear.com/LTC4000
9
相关PDF资料 |
PDF描述 |
|---|---|
| EBC22DRES-S734 | CONN EDGECARD 44POS .100 EYELET |
| EET-ED2G221DA | CAP ALUM 220UF 400V 20% SNAP |
| ESC06DRAS-S734 | CONN EDGECARD 12POS .100 R/A PCB |
| RCM12DCST | CONN EDGECARD 24POS DIP .156 SLD |
| EMC05DRAN-S734 | CONN EDGECARD 10POS .100 R/A PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4000EUFD#PBF | 功能描述:IC CHARGER BATTERY 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000EUFD#TRPBF | 功能描述:IC CHARGER BATTERY 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000EUFD-1#PBF | 功能描述:IC BATT CHRGR MULTI-CHEM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC4000EUFD-1#TRPBF | 功能描述:IC CHARGE MGMT MULTI CHEM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000IGN#PBF | 功能描述:IC CHARGER BATTERY 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。