- 您现在的位置：买卖IC网 > PDF目录16300 > LTC4000EGN#PBF (Linear Technology)IC CHARGER BATTERY 28-SSOP PDF资料下载
参数资料
| 型号： | LTC4000EGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/40页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY 28-SSOP |
| 产品培训模块： | LTC4000 60V Battery Charging Controller and Power Management |
| 标准包装： | 49 |
| 系列： | PowerPath™ |
| 功能： | 充电管理，电源管理 |
| 电池化学： | 多化学 |
| 电源电压： | 3 V ~ 60 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC4000
PIN FUNCTIONS
(QFN/SSOP)
V VM _ RST =
R VM1 + R VM2
? R ?
( 0.25μA ? R CX ) ? 0.5mV
I C / X =
VM(Pin1/Pin25): VoltageMonitorInput.Highimpedance
input to an accurate comparator with a 1.193V threshold
(typical). This pin controls the state of the RST output
pin. Connect a resistor divider (R VM1 , R VM2 ) between the
monitored voltage and GND, with the center tap point con-
nected to this pin. The falling threshold of the monitored
voltage is calculated as follows:
? 1.193V
R VM2
where R VM2 is the bottom resistor between the VM pin
and GND. Tie to the BIAS pin if voltage monitoring func-
tion is not used.
RST (Pin 2/Pin 26): High Voltage Open Drain Reset Output.
When the voltage at the VM pin is below 1.193V, this status
pin is pulled low. When driven low, this pin can disable
a DC/DC converter when connected to the converter’s
enable pin. This pin can also drive an LED to provide a
visual status indicator of a monitored voltage. Short this
pin to GND when not used.
IIMON (Pin 3/Pin 27): Input Current Monitor. The voltage
on this pin is 20 times (typical) the sense voltage (V IN,CLN )
across the input current sense resistor(R IS ), therefore
providing a voltage proportional to the input current.
Connect an appropriate capacitor to this pin to obtain a
voltage representation of the time-average input current.
Short this pin to GND to disable input current limit feature.
IL (Pin 4/Pin 28): Input Current Limit Programming. Con-
nect the input current programming resistor (R IL ) to this
pin. This pin sources 50μA of current. The regulation loop
compares the voltage on this pin with the input current
monitor voltage (V IIMON ), and drives the ITH pin accord-
ingly to ensure that the programmed input current limit is
not exceeded. The input current limit is determined using
the following formula:
I ILIM = 2.5μA ? ? IL ?
? R IS ?
where R IS is the sense resistor connected to the IN and
the CLN pins. Leave the pin open for the maximum input
current limit of 50mV/R IS .
ENC (Pin 5/Pin 1): Enable Charging Pin. High impedance
digital input pin. Pull this pin above 1.5V to enable charg-
ing and below 0.5V to disable charging. Leaving this pin
open causes the internal 2μA pull-up current to pull the
pin to 2.5V (typical).
IBMON (Pin 6/Pin 2): Battery Charge Current Monitor. The
voltage on this pin is 20 times (typical) the sense voltage
(V CSP,CSN ) across the battery current sense resistor (R CS ),
therefore providing a voltage proportional to the battery
charge current. Connect an appropriate capacitor to this
pin to obtain a voltage representation of the time-average
battery charge current. Short this pin to GND to disable
charge current limit feature.
CX (Pin 7/Pin 3): Charge Current Termination Pro-
gramming. Connect the charge current termination pro-
gramming resistor (R CX ) to this pin. This pin is a high
impedance input to a comparator and sources 5μA of
current. When the voltage on this pin is greater than the
charge current monitor voltage (V IBMON ), the CHRG pin
turns high impedance indicating that the CX threshold is
reached. When this occurs, the charge current is imme-
diately terminated if the TMR pin is shorted to the BIAS
pin, otherwise charging continues until the charge termi-
nation timer expires. The charge current termination value
is determined using the following formula:
R CS
Where R CS is the sense resistor connected to the CSP
and the CSN pins. Note that if R CX = R CL ≤ 19.1k?, where
R CL is the charge current programming resistor, then the
charge current termination value is one tenth the full charge
current, more familiarly known as C/10. Short this pin to
GND to disable CX termination.
CL (Pin 8/Pin 4): Charge Current Limit Programming. Con-
nect the charge current programming resistor (R CL ) to this
pin. This pin sources 50μA of current. The regulation loop
compares the voltage on this pin with the charge current
monitor voltage (V IBMON ), and drives the ITH pin accord-
ingly to ensure that the programmed charge current limit
4000fb
8
For more information www.linear.com/LTC4000
相关PDF资料 |
PDF描述 |
|---|---|
| EBC22DRES-S734 | CONN EDGECARD 44POS .100 EYELET |
| EET-ED2G221DA | CAP ALUM 220UF 400V 20% SNAP |
| ESC06DRAS-S734 | CONN EDGECARD 12POS .100 R/A PCB |
| RCM12DCST | CONN EDGECARD 24POS DIP .156 SLD |
| EMC05DRAN-S734 | CONN EDGECARD 10POS .100 R/A PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4000EUFD#PBF | 功能描述:IC CHARGER BATTERY 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000EUFD#TRPBF | 功能描述:IC CHARGER BATTERY 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000EUFD-1#PBF | 功能描述:IC BATT CHRGR MULTI-CHEM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC4000EUFD-1#TRPBF | 功能描述:IC CHARGE MGMT MULTI CHEM 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4000IGN#PBF | 功能描述:IC CHARGER BATTERY 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。