- 您现在的位置：买卖IC网 > PDF目录16300 > LTC4011CFE#PBF (Linear Technology)IC BATT CHARGER HIEFF 20TSSOP PDF资料下载
参数资料
| 型号： | LTC4011CFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/26页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER HIEFF 20TSSOP |
| 标准包装： | 74 |
| 功能： | 充电管理 |
| 电池化学： | 镍镉（NiCd）、镍金属氢化物（NiMH） |
| 电源电压： | 4.5 V ~ 34 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 20-TSSOP-EP |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
LTC4011
OPERATION
Top-Off Charge State
If NiMH fast charge termination occurs because the
?T/?t limit is exceeded after an initial period of t MAX /12
has expired, the LTC4011 enters the top-off charge state.
Top-off charge is implemented by sourcing one-tenth the
programmed charge current for t MAX /3 minutes to ensure
that 100% charge has been delivered to the battery. The
CHRG and TOC status outputs are active during the top-off
state. If NiCd cells have been selected with the CHEM pin,
the LTC4011 never enters the top-off state.
Automatic Recharge State
Once charging is complete, the automatic recharge state
is entered to address the self-discharge characteristics
of nickel chemistry cells. The charge status outputs are
inactive during automatic recharge, but V CDIV remains
switched to GND to monitor the average cell voltage. If the
V CELL voltage drops below 1.325V without falling below
350mV, the charge timer is reset and a new fast charge
cycle is initiated.
The internal termination algorithms of the LTC4011 are
adjusted when a fast charge cycle is initiated from auto-
matic recharge, because the battery should be almost fully
charged. Voltage-based termination is enabled immediately
and the NiMH ?T/?t limit is fixed at a battery temperature
rise of 1°C/minute.
Fault State
As discussed previously, the LTC4011 enters the fault state
based on detection of invalid battery voltages during vari-
ous charging phases. The IC also monitors the regulation
of the PWM control loop and will enter the fault state if
this is not within acceptable limits. Once in the fault state,
the battery must be removed or DC input power must be
cycled in order to initiate further charging. In the fault
state, the FAULT output is active, the READY output is
inactive, charging stops and the charge indicator outputs
are inactive. The V CDIV output remains connected to GND
to allow detection of battery removal.
resume when all temperatures return to acceptable levels.
Refer to the Status Outputs section for more detail.
Insertion and Removal of Batteries
The LTC4011 automatically senses the insertion or removal
of a battery by monitoring the V CELL pin voltage. Should
this voltage fall below 350mV, the IC considers the bat-
tery to be absent. Removing and then inserting a battery
causes the LTC4011 to initiate a completely new charge
cycle beginning with charge qualification.
External Pause Control
After charging is initiated, the V TEMP pin may be used to
pause operation at any time. When the voltage between
V TEMP and GND drops below 200mV, the charge timer
pauses, fast charge termination algorithms are inhibited
and the PWM outputs are disabled. The status and V CDIV
outputs all remain active. Normal function is fully restored
from the previous state when pause ends.
Status Outputs
The LTC4011 open-drain status outputs provide valuable
information about the IC’s operating state and can be
used for a variety of purposes in applications. Table 1
summarizes the state of the four status outputs and the
V CDIV pin as a function of LTC4011 operation. The status
outputs can directly drive current-limited LEDs terminated
to the DC input. The V CDIV column in Table 1is strictly
informational. V CDIV should only be used for the V CELL
resistor divider, as previously discussed.
Table 1. LTC4011 Status Pins
READY FAULT CHRG TOC V CDIV CHARGER STATE
Off Off Off Off Off Off
On Off Off Off On Ready to Charge
(V TEMP Held Low)
or Automatic Recharge
On Off On Off On Precharge or Fast Charge
(May be Paused)
On Off On On On NiMH Top-Off Charge
(May be Paused)
Note that the LTC4011 also uses the FAULT output to indi-
cate that charging is suspended due to invalid battery or
internal die temperatures. However, the IC does not enter
the fault state in these cases and normal operation will
On
Off
On
On
On or Off On or Off
Off Off
On
On
Temperature Limits
Exceeded
Fault State (Latched)
4011fb
相关PDF资料 |
PDF描述 |
|---|---|
| EEC49DRYS | CONN EDGECARD 98POS DIP .100 SLD |
| EMC12DRTN | CONN EDGECARD 24POS .100 EXTEND |
| 4-1906014-0 | CA 2.0MM OFNR 50/125,LC SEC YEL |
| ESC12DRTH | CONN EDGECARD 24POS DIP .100 SLD |
| LTC4010CFE#PBF | IC CHARGER NIMH/NICD 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4011CFETR | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011CFETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011EFE | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4012 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Effi ciency, Multi-Chemistry Battery Charger with PowerPath Control |
| LTC4012-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Effi ciency, Multi-Chemistry Battery Charger with PowerPath Control |
发布紧急采购，3分钟左右您将得到回复。