- 您现在的位置：买卖IC网 > PDF目录179918 > LTC4253AIGN#PBF (LINEAR TECHNOLOGY CORP) -48V Hot Swap Controller with Sequencer; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C PDF资料下载
参数资料
| 型号： | LTC4253AIGN#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | -48V Hot Swap Controller with Sequencer; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件页数： | 5/34页 |
| 文件大小： | 369K |
| 代理商： | LTC4253AIGN#PBF |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC4253/LTC4253A
13
425353afd
operaTion
Interlock Conditions
A start-up sequence commences once these “interlock”
conditions are met:
1. The input voltage VIN exceeds VLKO (UVLO).
2. The voltage at UV > VUVHI (VUV for the LTC4253A).
3. The voltage at OV < VOVLO (VOV – VOVHST for the
LTC4253A).
4. The input voltage at RESET < 0.8V.
5. The (SENSE – VEE) voltage < 50mV (VCB)
6. The voltage at SS is < 0.2V (20 VOS)
7. The voltage on the TIMER capacitor (CT)
is < 1V (VTMRL).
8. The voltage at GATE is < 0.5V (VGATEL)
The first four conditions are continuously monitored and
the latter four are checked prior to initial timing or GATE
ramp-up. Upon exiting an OV condition, the TIMER pin
voltage requirement is inhibited. Details are described in
the Applications Information, Timing Waveforms section.
If RESET < 0.8V occurs after the LTC4253/LTC4253A come
out of UVLO (interlock condition 1) and undervoltage (in-
terlock condition 2), GATE and SS are released without an
initial TIMER cycle once the other interlock conditions are
met (see Figure 13a). If not, TIMER begins the start-up
sequence by sourcing 5A into CT. If VIN, UV or OV falls
out of range or RESET asserts, the start-up cycle stops
and TIMER discharges CT to less than 1V, then waits until
the aforementioned conditions are once again met. If CT
successfully charges to 4V, TIMER pulls low and both SS
and GATE pins are released. GATE sources 50A (IGATE),
charging the MOSFET gate and associated capacitance.
The SS voltage ramp limits VSENSE to control the inrush
current. PWRGD1 pulls active low when GATE is within
2.8V of VIN and DRAIN is lower than VDRNL. This sets off
the power good sequence in which PWRGD2 and then
PWRGD3 is subsequently pulled low after a delay, adjust-
able through the SQTIMER capacitor CSQ or by external
control inputs EN2 and EN3. In this way, external loads
or power modules controlled by the three PWRGD signals
are turned on in a controlled manner without overloading
the power bus.
Two modes of operation are possible during the time the
MOSFET is first turned on, depending on the values of
externalcomponents,MOSFETcharacteristicsandnominal
design current. One possibility is that the MOSFET will
turn on gradually so that the inrush into the load capaci-
tance remains a low value. The output will simply ramp
to –48V and the LTC4253/LTC4253A will fully enhance
the MOSFET. A second possibility is that the load current
exceeds the soft-start current limit threshold of [VSS(t)/
20 – VOS]/RS. In this case the LTC4253/LTC4253A ramp
the output by sourcing soft-start limited current into the
load capacitance. If the soft-start voltage is below 1.2V,
the circuit breaker TIMER is held low. Above 1.2V, TIMER
ramps up. It is important to set the timer delay so that,
regardless of which start-up mode is used, the TIMER
ramp is less than one circuit breaker delay time. If this
condition is not met, the LTC4253/LTC4253A may shut
down after one circuit breaker delay time.
Board Removal
When the board is withdrawn from the card cage, the UV/
OV divider is the first to lose connection. This shuts off
the MOSFET and commutates the flow of current in the
connector. When the power pins subsequently separate
there is no arcing.
Current Control
Three levels of protection handle short-circuit and over-
load conditions. Load current is monitored by SENSE and
resistor RS. There are three distinct thresholds at SENSE:
50mV for a timed circuit breaker function; 100mV for an
analog current limit loop (60mV for the LTC4253A); and
200mV for a fast, feedforward comparator which limits
peak current in the event of a catastrophic short-circuit.
If, due to an output overload, the voltage drop across RS
exceeds50mV,TIMERsources200AintoCT.CTeventually
chargestoa4VthresholdandtheLTC4253/LTC4253Ashut
off. If the overload goes away before CT reaches 4V and
SENSE measures less than 50mV, CT slowly discharges
(5A). In this way the LTC4253/LTC4253A’s circuit breaker
function responds to low duty cycle overloads, and ac-
counts for the fast heating and slow cooling characteristic
of the MOSFET.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4253AIGN#TRPBF | -48V Hot Swap Controller with Sequencer; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| LTC4253CGN#PBF | -48V Hot Swap Controller with Sequencer; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C |
| LTC4253CGN#TRPBF | -48V Hot Swap Controller with Sequencer; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C |
| LTC4253IGN#PBF | -48V Hot Swap Controller with Sequencer; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| LTC4253IGN#TRPBF | -48V Hot Swap Controller with Sequencer; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4253BCGN#PBF | 功能描述:IC HOT SWAP CONTROLLER 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4253BCGN#PBF | 制造商:Linear Technology 功能描述:HOT SWAP CONTROLLER -48V SSOP-16 |
| LTC4253BCGN#TRPBF | 功能描述:IC HOT SWAP CONTROLLER 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC4253BIGN#PBF | 功能描述:IC HOT SWAP CONTROLLER 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4253BIGN#PBF | 制造商:Linear Technology 功能描述:HOT SWAP CONTROLLER -48V SSOP-16 |
发布紧急采购，3分钟左右您将得到回复。