- 您现在的位置：买卖IC网 > PDF目录262642 > LTC4267CGN-1#PBF (LINEAR TECHNOLOGY CORP) Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C PDF资料下载
参数资料
| 型号： | LTC4267CGN-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C |
| 中文描述： | 1 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件页数： | 20/32页 |
| 文件大小： | 925K |
| 代理商： | LTC4267CGN-1#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4267-1
27
42671f
If auxiliary power is applied directly to the LTC4267-1
switching regulator (bypassing the LTC4267-1 PD inter-
face), a different set of tradeoffs arise. In the conguration
shown in option 2, the wall transformer does not need
to exceed the LTC4267-1 turn-on UVLO requirement;
however, it is necessary to include diode D9 to prevent
the transformer from applying power to the LTC4267-1
interface controller. The transformer voltage requirement
will be governed by the needs of the onboard switching
regulator. However, power priority issues require more
intervention. If the wall transformer voltage is below
the PSE voltage, then priority will be given to the PSE
power. The LTC4267-1 interface controller will draw power
from the PSE while the transformer will sit unused. This
conguration is not a problem in a PoE system. On the
other hand, if the wall transformer voltage is higher than
the PSE voltage, the LTC4267-1 switching regulator will
draw power from the transformer. In this situation, it is
necessary to address the issue of power cycling that may
occur if a PSE is present. The PSE will detect the PD and
apply power. If the switcher is being powered by the wall
transformer, then the PD will not meet the minimum load
requirement and the PSE will subsequently remove power.
The PSE will again detect the PD and power cycling will
start. With a transformer voltage above the PSE voltage,
it is necessary to either disable the signature, as shown
in option 2, or install a minimum load on the output of the
LTC4267-1 interface to prevent power cycling.
The third option also applies power directly to the
LTC4267-1 switching regulator, bypassing the LTC4267-1
interface controller and omitting diode D9. With the
diode omitted, the transformer voltage is applied to the
LTC4267-1 interface controller in addition to the switching
regulator. For this reason, it is necessary to ensure that the
transformer maintain the voltage between 38V and 57V
to keep the LTC4267-1 interface controller in its normal
operating range. The third option has the advantage of
automatically disabling the 25k signature resistor when
the external voltage exceeds the PSE voltage.
Power-Up Sequencing the LTC4267-1
The LTC4267-1 consists of two functional cells, the PD
interface and the switching regulator, and the power up
sequencing of these two cells must be carefully considered.
The PD designer should ensure that the switching regulator
does not begin operation until the interface has completed
charging up the load capacitor. This will ensure that the
switcher load current does not compete with the load
capacitor charging current provided by the PD interface
current limit circuit. Overlooking this consideration may
result in slow power supply ramp up, power-up oscillation,
and possibly thermal shutdown.
The LTC4267-1 includes a power good signal in the PD
interface that can be used to indicate to the switching
regulator that the load capacitor is fully charged and ready
to handle the switcher load. Figure 7 shows two examples
of ways the
PWRGD signal can be used to control the
switching regulator. The rst example employs an N-chan-
nel MOSFET to drive the ITH/RUN port below the shutdown
threshold (typically 0.28V). The second example drives
PVCC below the PVCC turn-off threshold. Employing the
second example has the added advantage of adding delay
to the switching regulator start-up beyond the time the
power good signal becomes active. The second example
ensures additional timing margin at start-up without the
need for added delay components. In applications where it
is not desirable to utilize the power good signal, sufcient
timing margin can be achieved with RSTART and CPVCC.
RSTART and CPVCC should be set to a delay of two to three
times longer than the duration needed to charge up C1.
Layout Considerations for the LTC4267-1
The most critical layout considerations for the LTC4267-1
are the placement of the supporting external components
associated with the switching regulator. Efciency, stability,
and load transient response can deteriorate without good
layout practices around critical components.
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4267CGN-1#TRPBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C |
| LTC4267IGN-1#PBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| LTC4267IGN-1#TRPBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| LPO3310-102MLB | Power inductor, 20% tol, SMT, RoHS |
| LPO3310-102MLC | Power inductor, 20% tol, SMT, RoHS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4267CGN-1-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
| LTC4267CGN-1-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
| LTC4267CGN-3#PBF | 功能描述:IC POE 802.3AF W/REG 16-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CGN-3#TRPBF | 功能描述:IC POE 802.3AF INTERFACE 16SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CGNPBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-Ch -57V SSOP16 |
发布紧急采购，3分钟左右您将得到回复。