- 您现在的位置：买卖IC网 > PDF目录262642 > LTC4267CGN-1#PBF (LINEAR TECHNOLOGY CORP) Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C PDF资料下载
参数资料
| 型号： | LTC4267CGN-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C |
| 中文描述： | 1 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件页数： | 8/32页 |
| 文件大小： | 925K |
| 代理商： | LTC4267CGN-1#PBF |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4267-1
16
42671f
Adjustable Slope Compensation
The LTC4267-1 switching regulator injects a 5μA peak
current ramp out through its SENSE pin which can be
used for slope compensation in designs that require it.
This current ramp is approximately linear and begins at
zero current at 6% duty cycle, reaching peak current at
80% duty cycle. Programming the slope compensation
via a series resistor is discussed in the External Interface
and Component Selection section.
EXTERNAL INTERFACE AND COMPONENT SELECTION
Input Interface Transformer
Nodes on an Ethernet network commonly interface to the
outside world via an isolation transformer (Figure 9). For
PoE devices, the isolation transformer must include a
center tap on the media (cable) side. Proper termination
is required around the transformer to provide correct
impedance matching and to avoid radiated and conducted
emissions. Transformer vendors such as Bel Fuse, Coil-
craft, Pulse and Tyco (Table 3) can provide assistance with
selection of an appropriate isolation transformer and proper
termination methods. These vendors have transformers
specically designed for use in PD applications.
Table 3. Power over Ethernet Transformer Vendors
VENDOR
CONTACT INFORMATION
Bel Fuse Inc.
206 Van Vorst Street
Jersey City, NJ 07302
Tel: 201-432-0463
FAX: 201-432-9542
http://www.belfuse.com
Coilcraft, Inc.
1102 Silver Lake Road
Cary, IL 60013
Tel: 847-639-6400
FAX: 847-639-1469
http://www.coilcraft.com
Pulse Engineering
12220 World Trade Drive
San Diego, CA 92128
Tel: 858-674-8100
FAX: 858-674-8262
http://www.pulseeng.com
Tyco Electronics
308 Constitution Drive
Menlo Park, CA 94025-1164
Tel: 800-227-7040
FAX: 650-361-2508
http://www.circuitprotection.com
APPLICATIO S I FOR ATIO
WU
UU
Figure 8. LTC4267-1 Switching Regulator
Start-Up/Shutdown State Diagram
The undervoltage lockout mechanism on PVCC prevents
the LTC4267-1 switching regulator from trying to drive
the external N-Channel MOSFET with insufcient gate-to-
source voltage. The voltage at the PVCC pin must exceed
VTURNON (nominally 8.7V with respect to PGND) at least
momentarily to enable operation. The PVCC voltage must
fall to VTURNOFF (nominally 5.7V with respect to PGND)
before the undervoltage lockout disables the switching
regulator. This wide UVLO hysteresis range supports
applications where a bias winding on the yback trans-
former is used to increase the efciency of the LTC4267-1
switching regulator.
TheITH/RUNcanbedrivenbelowVITHSHDN(nominally0.28V
with respect to PGND) to force the LTC4267-1 switching
regulator into shutdown. An internal 0.3μA current source
always tries to pull the ITH/RUN pin towards PVCC. When
the ITH/RUN pin voltage is allowed to exceed VITHSHDN and
PVCC exceeds VTURNON, the LTC4267-1 switching regulator
begins to operate and an internal clamp immediately pulls
the ITH/RUN pin to about 0.7V. In operation, the ITH/RUN
pin voltage will vary from roughly 0.7V to 1.9V to represent
current comparator thresholds from zero to maximum.
Internal Soft-Start
An internal soft-start feature is enabled whenever the
LTC4267-1 switching regulator comes out of shutdown.
Specically, the ITH/RUN voltage is clamped and is
prevented from reaching maximum until 1.4ms have
passed. This allows the input current of the PD to rise in a
smooth and controlled manner on start-up and stay within
the current limit requirement of the LTC4267-1 interface.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4267CGN-1#TRPBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C |
| LTC4267IGN-1#PBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| LTC4267IGN-1#TRPBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| LPO3310-102MLB | Power inductor, 20% tol, SMT, RoHS |
| LPO3310-102MLC | Power inductor, 20% tol, SMT, RoHS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4267CGN-1-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
| LTC4267CGN-1-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
| LTC4267CGN-3#PBF | 功能描述:IC POE 802.3AF W/REG 16-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CGN-3#TRPBF | 功能描述:IC POE 802.3AF INTERFACE 16SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CGNPBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-Ch -57V SSOP16 |
发布紧急采购，3分钟左右您将得到回复。