- 您现在的位置：买卖IC网 > PDF目录262642 > LTC4267CGN-1#PBF (LINEAR TECHNOLOGY CORP) Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C PDF资料下载
参数资料
| 型号： | LTC4267CGN-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C |
| 中文描述： | 1 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件页数： | 27/32页 |
| 文件大小： | 925K |
| 代理商： | LTC4267CGN-1#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页
LTC4267-1
4
42671f
The
● denotes the specications which apply over the full operating
temperature range, otherwise specications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
tRISE
NGATE Drive Rise Time
CLOAD = 3000pF, PVCC – PGND = 8V
40
ns
tFALL
NGATE Drive Fall Time
CLOAD = 3000pF, PVCC – PGND = 8V
40
ns
VIMAX
Peak Current Sense Voltage
RSL = 0, PVCC – PGND = 8V (Note 15)
●
90
100
115
mV
ISLMAX
Peak Slope Compensation Output Current
PVCC – PGND = 8V (Note 16)
5
μA
tSFST
Soft-Start Time
PVCC – PGND = 8V
1.4
ms
TSHUTDOWN
Thermal Shutdown Trip Temperature
(Notes 13, 17)
140
°C
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: PVCC internal clamp circuit self regulates to 9.4V with respect to
PGND.
Note 3: The LTC4267-1 operates with a negative supply voltage in the
range of – 1.5V to – 57V. To avoid confusion, voltages for the PD interface
are always referred to in terms of absolute magnitude. Terms such as
“maximum negative voltage” refer to the largest negative voltage and
a “rising negative voltage” refers to a voltage that is becoming more
negative.
Note 4: The LTC4267-1 is designed to work with two polarity protection
diode drops between the PSE and PD. Parameter ranges specied in the
Electrical Characteristics section are with respect to this product pins and
are designed to meet IEEE 802.3af specications when these diode drops
are included. See the Application Information section.
Note 5: Signature resistance is measured via the two-point
ΔV/ΔI method
as dened by IEEE 802.3af. The PD signature resistance is offset from
the 25k to account for diode resistance. With two series diodes, the total
PD resistance will be between 23.75k and 26.25k and meet IEEE 802.3af
specications. The minimum probe voltages measured at the LTC4267-1
pins are –1.5V and –2.5V. The maximum probe voltages are –8.5V and
–9.5V.
Note 6: The PD interface includes hysteresis in the UVLO voltages to
preclude any start-up oscillation. Per IEEE 802.3af requirements, the PD
will power up from a voltage source with 20
Ω series resistance on the rst
trial.
Note 7: Dynamic Supply current is higher due to the gate charge being
delivered at the switching frequency.
Note 8: IVPORTN_CLASS does not include classication current
programmed at the RCLASS pin. Total current in classication mode will be
IVPORTN_CLASS + ICLASS (See note 9).
Note 9: ICLASS is the measured current owing through RCLASS. ΔICLASS
accuracy is with respect to the ideal current dened as ICLASS = 1.237/
RCLASS. The current accuracy does not include variations in RCLASS
resistance. The total classication current for a PD also includes the IC
quiescent current (IVPORTN_CLASS). See Applications Information.
Note 10: To disable the 25k signature, tie SIGDISA to VPORTP or hold
SIGDISA high with respect to VPORTN. See Applications Information.
Note 11: The switching regulator is tested in a feedback loop that servos
VFB to the output of the error amplier while maintaining ITH/RUN at the
midpoint of the current limit range.
Note 12: IPOUT_LEAK includes current drawn through POUT by the power
good status circuit. This current is compensated for in the 25k signature
resistance and does not affect PD operation.
Note 13: The LTC4267-1 PD Interface includes thermal protection. In
the event of an overtemperature condition, the PD interface will turn off
the switching regulator until the part cools below the overtemperature
limit. The LTC4267-1 is also protected against thermal damage from
incorrect classication probing by the PSE. If the LTC4267-1 exceeds the
overtemperature threshold, the classication load current is disabled.
Note 14: The PD interface includes dual level input current limit. At turn-
on, before the POUT load capacitor is charged, the PD current level is set
to a low level. After the load capacitor is charged and the POUT – VPORTN
voltage difference is below the power good threshold, the PD switches to
high level current limit. The PD stays in high level current limit until the
input voltage drops below the UVLO turn-off threshold.
Note 15: Peak current sense voltage is reduced dependent on duty cycle
and an optional external resistor in series with the SENSE pin (RSL). For
details, refer to the programmable slope compensation feature in the
Applications Information section.
Note 16: Guaranteed by design.
Note 17: The PD interface includes overtemperature protection that is
intended to protect the device from momentary overload conditions.
Junction temperature will exceed 125°C when overtemperature protection
is active. Continuous operation above the specied maximum operating
junction temperature may impair device reliability.
ELECTRICAL CHARACTERISTICS
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4267CGN-1#TRPBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: 0°C to +70°C |
| LTC4267IGN-1#PBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| LTC4267IGN-1#TRPBF | Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator; Package: SSOP; No of Pins: 16; Temperature Range: -40°C to +85°C |
| LPO3310-102MLB | Power inductor, 20% tol, SMT, RoHS |
| LPO3310-102MLC | Power inductor, 20% tol, SMT, RoHS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4267CGN-1-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
| LTC4267CGN-1-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
| LTC4267CGN-3#PBF | 功能描述:IC POE 802.3AF W/REG 16-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CGN-3#TRPBF | 功能描述:IC POE 802.3AF INTERFACE 16SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4267CGNPBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-Ch -57V SSOP16 |
发布紧急采购，3分钟左右您将得到回复。