- 您现在的位置：买卖IC网 > PDF目录20347 > LTC4414IMS8#PBF (Linear Technology)IC CNTRLR POWERPATH 8-MSOP PDF资料下载
参数资料
| 型号： | LTC4414IMS8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR POWERPATH 8-MSOP |
| 标准包装： | 50 |
| 系列： | PowerPath™ |
| 应用： | 电池备份，工业/汽车，大电流开关 |
| FET 型： | P 沟道 |
| 输出数： | 1 |
| 内部开关： | 无 |
| 延迟时间 - 开启： | 600µs |
| 延迟时间 - 关闭： | 20µs |
| 电源电压： | 3 V ~ 36 V |
| 电流 - 电源： | 33µA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
LTC4414
OPERATIO
Operation can best be understood by referring to the Block
Diagram, which illustrates the internal circuit blocks along
with the few external components, and the graph that
accompanies the Typical Application drawing on the front
page of the data sheet. The terms primary and auxiliary are
arbitrary and may be changed to suit the application.
Operation begins when either or both power sources are
applied and the CTL control pin is below the input low
voltage of 0.35V (V IL ). If only the primary supply is
present, the Power Source Selector will power the LTC4414
from the V IN pin. Amplifier A1 will deliver a current to the
Analog Controller block that is proportional to the voltage
difference in the V IN and SENSE pins. While the voltage on
SENSE is lower than V IN – 20mV (V FR ), the Analog
Controller will instruct the Linear Gate Driver and Voltage
Clamp block to pull down the GATE pin voltage and turn on
the external P-channel MOSFET. The dynamic pull-down
current of 300 μ A (I G(SNK) ) stops when the GATE voltage
reaches ground or the gate clamp voltage. The gate clamp
voltage is 8.5V (V G(ON) ) below the higher of V IN or V SENSE .
As the SENSE voltage pulls up to V IN – 20mV, the LTC4414
will regulate the GATE voltage to maintain a 20mV differ-
ence between V IN and V SENSE which is also the V DS of the
MOSFET. The system is now in the forward regulation
mode and the load will be powered from the primary
supply. As the load current varies, the GATE voltage will be
controlled to maintain the 20mV difference. If the load
current exceeds the P-channel MOSFET’s ability to deliver
the current with a 20mV V DS the GATE voltage will clamp,
the MOSFET will behave as a fixed resistor and the forward
voltage will increase slightly. While the MOSFET is on the
STAT pin is an open circuit.
When an auxiliary supply is applied, the SENSE pin will be
The Power Source Selector will power the LTC4414
from the SENSE pin. As the SENSE voltage pulls above
V IN – 20mV, the Analog Controller will instruct the Linear
Gate Driver and Voltage Clamp block to pull the GATE
voltage up to turn off the P-channel MOSFET. When the
voltage on SENSE is higher than V IN + 20mV (V RTO ), the
Analog Controller will instruct the Linear Gate Driver and
Voltage Clamp block to rapidly pull the GATE pin voltage
to the SENSE pin voltage. This action will quickly finish
turning off the external P-channel MOSFET if it hasn’t
already turned completely off. For a clean transition, the
reverse turn-off threshold has hysteresis to prevent
uncertainty. The system is now in the reverse turn-off
mode. Power to the load is being delivered through the
external diode and no current is drawn from the primary
supply. The external diode provides protection in case
the auxiliary supply is below the primary supply, sinks
current to ground or is connected reverse polarity.
During the reverse turn-off mode of operation the STAT
pin will sink a current (I S(SNK) ) if connected. Note that the
external MOSFET is wired so that the drain to source
diode will momentarily forward bias when power is first
applied to V IN and will become reverse biased when an
auxiliary supply is applied.
When the CTL (control) input is asserted high, the external
MOSFET will have its gate to source voltage forced to a
small voltage V G(OFF) and the STAT pin will sink a mini-
mum of 50 μ A of current if connected. This feature is useful
to allow control input switching of the load between two
power sources as shown in Figure 3 or as a switchable
high side driver as shown in Figure 7. A 3.5 μ A internal pull-
down current (I CTL ) on the CTL pin will insure a low level
input if the pin should become open.
pulled higher than the V IN pin through the external diode.
4414fc
6
相关PDF资料 |
PDF描述 |
|---|---|
| GMA06DTAH | CONN EDGECARD 12POS R/A .125 SLD |
| VI-B6H-CW-F2 | CONVERTER MOD DC/DC 52V 100W |
| ES2A-13 | RECT SUPER FAST SMD 50V 2A SMB |
| 395-100-541-204 | CARD EDGE 100PS DL .100X.200 BLK |
| S120J25U2JR6BV7R | CAP CER 12PF 3KV 5% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4415EDHC#PBF | 功能描述:IC DUAL 4A DIODES 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4415EDHC#TRPBF | 功能描述:IC DUAL 4A DIODES 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4415EMSE#PBF | 功能描述:IC DUAL 4A DIODES 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4415EMSE#TRPBF | 功能描述:IC DUAL 4A DIODES 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4415IDHC#PBF | 功能描述:IC DUAL 4A DIODES 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。