- 您现在的位置：买卖IC网 > PDF目录20045 > LTC5100EUF (Linear Technology)IC DRIVER VCSEL 3.2GBPS 16QFN PDF资料下载
参数资料
| 型号： | LTC5100EUF |
| 厂商： | Linear Technology |
| 文件页数： | 19/52页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER VCSEL 3.2GBPS 16QFN |
| 标准包装： | 91 |
| 类型： | 激光二极管驱动器 |
| 数据速率： | 3.2Gbps |
| 通道数： | 1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 54mA |
| 电流 - 调制： | 12mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN（4x4） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC5100
OPERATIO
monitor photodiode current. In each case the fundamental
calculation is the same. The LTC5100’s digital controller
multiplies the nominal value of the quantity (I B , I M or I MD )
by a quadratic function of temperature. Temperature mea-
surements are supplied either by an on-chip temperature
sensor or by an external microprocessor, according to the
setting of Ext_temp_en. The general temperature com-
pensation formula is:
I = I_nom ? (TC2 ? 2 –18 ? ? T 2 + TC1 ? 2 –13 ? ? T + 1) (12)
where I is the digital representation of the laser bias
current, modulation current or monitor diode current (I B ,
I M or I MD ).
When using the internal temperature sensor (Ext_temp_en
= 0), the temperature measurements are taken by the on-
chip ADC, and ? T is the change in the LTC5100 die tem-
perature relative to a user defined nominal temperature:
? T = T_int_adc – T_nom (13)
When using an external temperature source (Ext_temp_en
= 1), the temperature measurements are provided in
digital form by a microprocessor or host computer and ? T
is the change in temperature relative to a user defined
nominal temperature:
? T = T_ext –T_nom (14)
T_int_adc, T_ext, and T_nom are 10-bit, unsigned numbers
scaled at 0.5K/LSB. The maximum temperature that can be
represented is therefore 2 10 ? 0.5 ° K = 512 ° K or 239 ° C.
TC1 and TC2 are the first and second order temperature
coefficients. They correspond to the registers Im_tc1 and
Im_tc2 for modulation current, Ib_tc1 and Ib_tc2 for bias
current and Imd_tc1 and Imd_tc2 for monitor diode
current. In each case TC1 and TC2 are 8-bit signed
numbers in two’s complement format. The range of the
temperature coefficients is therefore –128 to +127. When
TC1 is multiplied by its weighting coefficient of 2 –13 in
Equation 12, the effective value of the first order tempera-
ture coefficient is 122ppm/ ° C per LSB. The full-scale
range is approximately ± 15500 ppm/ ° C. When TC2 is
multiplied by its weighting coefficient of 2 –18 in Equation
12, the effective value of the second order temperature
coefficient is 3.81ppm/ ° C 2 per LSB. The full-scale range is
approximately ± 484 ppm/ ° C 2 .
Note that Equation 12 is applied to the digital representa-
tion of the currents, not the physical current themselves.
This is a particularly important point where monitor diode
current is concerned, because the digital representation of
the monitor diode current is the logarithm of the current.
Thus the temperature compensation is of the logarithm of
the monitor diode current and not the current itself.
Notation Used for Registers and Bit Fields
The LTC5100 has a large set of registers, many of which
are subdivided into fields of bits. Register names are given
in all capitals (SYS_CONFIG) and bit fields are given in
mixed case (Apc_en). For example, the bit that enables
Automatic Power Control mode is contained in the System
Configuration register. This bit is denoted by:
SYS_CONFIG.Apc_en
In many cases this bit field will simply be referred to as
“Apc_en.”
The functional diagrams of Figure 3 and Figure 4 show
registers and bit fields within registers between horizontal
bars. For example, the “Data” field in the ADC register is
shown as:
USER_ADC.Data
A write operation to this register is shown as:
USER_ADC.Data
A register read operation is shown as:
Peaking
Range Selection for the Source
and Modulation Currents
The source and modulation currents each have four ranges
of operation to optimize ADC and DAC resolution as well
as high frequency performance. The source current range
is controlled by two bits called Is_rng. Similarly, the modu-
lation current range is controlled by two bits called Im_rng.
The maximum current that can be delivered is proportional
to the range, so the current output is 1, 2, 3 or 4 times the
typical base value of 9mA for the source current and
4.5mA for the average modulation current or 9mA peak-
to-peak.
sn5100 5100fs
19
相关PDF资料 |
PDF描述 |
|---|---|
| AMC19DRTH-S734 | CONN EDGECARD 38POS DIP .100 SLD |
| T86D476M010EAAL | CAP TANT 47UF 10V 20% 2917 |
| VE-240-CX-F4 | CONVERTER MOD DC/DC 5V 75W |
| TACL105K010XTA | CAP TANT 1UF 10V 10% 0603 |
| T86D476K010EAAL | CAP TANT 47UF 10V 10% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC5100EUF#PBF | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC5100EUF#TR | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC5100EUF#TRPBF | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC511P | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LTC5336E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
发布紧急采购，3分钟左右您将得到回复。