- 您现在的位置：买卖IC网 > PDF目录20045 > LTC5100EUF (Linear Technology)IC DRIVER VCSEL 3.2GBPS 16QFN PDF资料下载
参数资料
| 型号： | LTC5100EUF |
| 厂商： | Linear Technology |
| 文件页数： | 30/52页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER VCSEL 3.2GBPS 16QFN |
| 标准包装： | 91 |
| 类型： | 激光二极管驱动器 |
| 数据速率： | 3.2Gbps |
| 通道数： | 1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 54mA |
| 电流 - 调制： | 12mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN（4x4） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC5100
OPERATIO
Conversion Sequence
The ADC has a 1ms conversion time and operates in a four-
cycle sequence. Three of these cycles are dedicated to the
needs of the servo controllers for laser bias and modula-
tion current. One cycle is available to the user to convert
any desired quantity. Table 2 shows how the four conver-
sion time slots are allocated. The temperature compensa-
tion and servo loop calculations are done during the User
cycle. The source and modulation DACs are also updated
during this cycle.
Table 2. ADC Conversion Sequence
writing the USER_ADC register clears the Valid bit. The
Valid bit remains cleared until the next user conversion is
complete. USER_ADC.Adc_src always corresponds to
the signal source whose data is stored in USER_ADC.Data,
not the source that was most recently selected by writing
USER_ADC.Adc_src_sel. The Valid bit and ADC_src field
are useful for monitoring when the ADC has updated the
USER_ADC.Data field. Table 3 gives an extended example
of accessing the USER_ADC register.
Note that the content of the USER_ADC register is different
for writing and for reading, even though the I 2 C command
CYCLE
1
2
3
4
APC MODE
T
I M
I MD
User
CCC MODE
T
I M
I S
User
RESULT STORED IN
REGISTER
T_INT_ADC
IM_ ADC
IMD_ADC/IS_ADC
USER_ADC
used to access this register is the same in both cases. See
Table 23 and Table 24 for a detailed definition of the bit
fields in the USER_ADC register. Table 23 also shows how
to convert ADC digital codes to real-world quantities.
DIRECT MICROPROCESSOR CONTROL OF THE LASER
BIAS AND MODULATION CURRENT
User Access to the ADC
The results of each conversion cycle in Table 2 are stored
in user accessible registers. The last die temperature
measurement can be read over the I 2 C bus at any time by
reading the T_INT_ADC register. Note that the quantity
converted during the third cycle depends on whether the
chip is in APC or CCC mode. The result of the third
conversion cycle is stored in a register that is called
IMD_ADC in APC mode and IS_ADC in CCC mode. There
is only one register, but it is given two names to indicate
the quantity it actually holds.
The fourth cycle, called the user cycle, is available to
digitize any of the six multiplexed signals. The result can
be read out over the I 2 C serial bus. The signal to be
digitized during the user cycle is selected by setting the
three-bit field USER_ADC.Adc_src_sel (see Table 23).
For example, setting Adc_ src_sel = 2 programs the
multiplexer to select the laser diode voltage, V LD . During
the next user conversion cycle, V LD is converted and
stored to the USER_ADC. Data field. When the conversion
is complete, USER_ADC.Valid is set and
USER_ADC.Adc_src indicates the signal source whose
converted value is stored in USER_ADC.Data. Reading or
Setting Lpc_en to zero turns off the LTC5100’s digital
Laser Power Controller (see Figure 2). The source and
modulation DACs (Is_dac and Im_dac) can then be written
from the I 2 C serial bus, allowing an external microproces-
sor or test computer to directly control the source and
modulation currents.
DIGITAL CONTROL AND THE I 2 C SERIAL INTERFACE
The LTC5100 has extensive digital control and monitoring
features. These features can be used during final assembly
of a transceiver module to set up the laser and verify
performance. In normal operation, the LTC5100 can oper-
ate standalone or under microprocessor supervision. Op-
erating standalone, the LTC5100 automatically loads its
configuration and laser operating parameters (bias cur-
rent, modulation current, monitor diode current) from a
small external EEPROM at power up. Operating under
microprocessor supervision, the microprocessor is in
total control of setting up the LTC5100.
I 2 C Serial Interface Protocol
The digital interface for the LTC5100 is I 2 C, a 2-wire serial
bus standard that is fully documented in “I 2 C-Bus and How
sn5100 5100fs
30
相关PDF资料 |
PDF描述 |
|---|---|
| AMC19DRTH-S734 | CONN EDGECARD 38POS DIP .100 SLD |
| T86D476M010EAAL | CAP TANT 47UF 10V 20% 2917 |
| VE-240-CX-F4 | CONVERTER MOD DC/DC 5V 75W |
| TACL105K010XTA | CAP TANT 1UF 10V 10% 0603 |
| T86D476K010EAAL | CAP TANT 47UF 10V 10% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC5100EUF#PBF | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC5100EUF#TR | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC5100EUF#TRPBF | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC511P | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LTC5336E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
发布紧急采购，3分钟左右您将得到回复。