- 您现在的位置：买卖IC网 > PDF目录20045 > LTC5100EUF (Linear Technology)IC DRIVER VCSEL 3.2GBPS 16QFN PDF资料下载
参数资料
| 型号： | LTC5100EUF |
| 厂商： | Linear Technology |
| 文件页数： | 49/52页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER VCSEL 3.2GBPS 16QFN |
| 标准包装： | 91 |
| 类型： | 激光二极管驱动器 |
| 数据速率： | 3.2Gbps |
| 通道数： | 1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 54mA |
| 电流 - 调制： | 12mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN（4x4） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页当前第49页第50页第51页第52页
LTC5100
APPLICATIO S I FOR ATIO
Figure 31 and Figure 32 show the schematic and layout of
a minimum reflection coefficient, minimum peaking solu-
tion. Two capacitors, C1 and C2 are used to further reduce
the inductance in the termination network. C2 has two vias
to the ground plane.
TEMPERATURE COMPENSATION
The LTC5100 has first and second order digital tempera-
ture compensation for the laser bias current, laser modu-
lation current, and monitor diode current. Recall that in
constant current control mode, the LTC5100 provides
direct temperature compensation of the laser bias current
and the laser modulation current. In automatic power
control mode, the laser bias current is under closed-loop
control and the LTC5100 provides temperature compen-
sation for the monitor diode current and the laser modu-
lation current. The simplest procedure for determining the
temperature coefficients (TC1 and TC2 in Equation 12,
Equation 18, Equation 23, and Equation 29) is as follows:
? Select a nominal or representative laser diode and
assemble it into a transceiver module with the LTC5100.
? Set all temperature coefficients to zero.
? Place the transceiver module in a temperature chamber
and find the values of Ib_nom, Im_nom, and Imd_nom
that give constant average optical power and extinction
ratio at several temperature points.
? Record the LTC5100’s temperature reading, T_int, at
each temperature point.
? Select a convenient value for T_nom, the nominal tem-
perature. (It is customary, but not mandatory, to use
25 ° C for the nominal temperature.)
? Find the best values of TC1 and TC2 by fitting the
quadratic temperature compensation formula (Equa-
tion 12) to the experimental values of Ib_nom, Im_nom,
Imd_nom, and T_int.
To configure the LTC5100 for normal operation, set the
nominal current to the value found at the nominal tem-
perature. Set TC1 and TC2 to the values determined by the
best fit of the data. For standalone operation, store these
values in the EEPROM. For microprocessor operation,
store the values in the microprocessor’s internal non-
volatile memory or in another source of nonvolatile memory
and load them into the LTC5100 after power-up.
The above procedure not only corrects for the laser
temperature drift, but also corrects the small temperature
drift found in the LTC5100’s internal references.
DEMONSTRATION BOARD
Figure 33 shows the schematic of the DC499 demonstra-
tion board. Details of the use of this demo board and
accompanying software can be found in the DC499 demo
board manual. Figure 34 shows the layout of the demo
board and Table 31 gives the bill of materials for the demo
board.
The core applications circuit for the LTC5100 VCSEL
driver appears inside the box in Figure 33. This is the
complete circuit for an optical transceiver module, includ-
ing power supply filtering. It consists of the LTC5100 with
EEPROM for storing setup parameters, L1 and C3 for
power supply filtering, and R1, C1, and C2 for terminating
the 50 ? modulation output. The circuitry outside the box
in Figure 33 is for support of the demonstration. 5V power
enters through 2-pin connector P2 and is regulated by U3
to 3.3V to power the LTC5100. Connector P1 sends 5V
power and serial control signals to another board, allow-
ing a personal computer to control the LTC5100. U4
produces 1.8VDC to bias the modulation output for elec-
trical eye measurements.
High speed data enters the LTC5100 through SMA con-
nectors J1 and J2. The LTC5100 high speed inputs are
internally AC coupled with rail-to-rail common mode input
voltage range. The input signal swing can go as much as
300mV above V DD or below V SS without degrading perfor-
mance or causing excessive current flow. The high speed
inputs may be AC coupled, in which case the common
mode voltage floats to mid-supply or 1.65V nominally.
A common cathode VCSEL can be attached to the demo
board via SMA connector J3. R1 establishes a precision,
low reflection coefficient 50 ? modulation drive. By main-
taining a wide band microwave quality 50 ? path, the
length of the connection to the laser can be arbitrarily long.
The LTC5100 generates 20% to 80% transition times of
60ps (80ps 10% to 90%), corresponding to an instanta-
neous transition filtered by a 4.4GHz Gaussian lowpass
filter. At these speeds the primary limitation on line length
is high frequency loss. For high grade, low loss laboratory
cabling with silver coated center conductor and foamed
PTFE dielectric, a practical limit is about 30cm.
sn5100 5100fs
49
相关PDF资料 |
PDF描述 |
|---|---|
| AMC19DRTH-S734 | CONN EDGECARD 38POS DIP .100 SLD |
| T86D476M010EAAL | CAP TANT 47UF 10V 20% 2917 |
| VE-240-CX-F4 | CONVERTER MOD DC/DC 5V 75W |
| TACL105K010XTA | CAP TANT 1UF 10V 10% 0603 |
| T86D476K010EAAL | CAP TANT 47UF 10V 10% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC5100EUF#PBF | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC5100EUF#TR | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC5100EUF#TRPBF | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC511P | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LTC5336E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
发布紧急采购，3分钟左右您将得到回复。