- 您现在的位置：买卖IC网 > PDF目录20045 > LTC5100EUF (Linear Technology)IC DRIVER VCSEL 3.2GBPS 16QFN PDF资料下载
参数资料
| 型号： | LTC5100EUF |
| 厂商： | Linear Technology |
| 文件页数： | 25/52页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER VCSEL 3.2GBPS 16QFN |
| 标准包装： | 91 |
| 类型： | 激光二极管驱动器 |
| 数据速率： | 3.2Gbps |
| 通道数： | 1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 54mA |
| 电流 - 调制： | 12mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN（4x4） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC5100
OPERATIO
Equation 20 shows that the loop gain is completely inde-
pendent of the slope efficiency and monitor diode re-
sponse. Consequently the servo dynamics and settling
microprocessor, according to the setting of Ext_temp_en.
The temperature compensated expression for Imd_set is
given by:
? + Im d _ tc 1 ? 2 – 13 ? ? T + 1 ?
time are independent of these highly varying quantities.
The Apc_gain quantity can be set to compensate for the
selected values of Is_rng and Im_rng as well as the
extinction ratio, termination resistance and laser dynamic
resistance.
Im d _ set =
? Im d _ tc 2 ? 2 – 18 ? ? T 2 ?
Im d _ nom ? ? ?
(23)
The step response of the APC loop is:
Imd_adc n = Imd_set ? [1 – (1 – A) n ]
(22)
Imd_tc1 and Imd_tc2 are the first and second order
temperature coefficients for the monitor diode current.
Equation 23 applies to the digital representation of the
The step response given in Equation 22 has the familiar
exponential settling characteristic of a first order system.
The step response is shown in Figure 25 for A = 0.5. The
remaining error is reduced by one-half with each servo
iteration. In seven iterations, or about 28ms, the modula-
tion current settles to under 1% in this example. The
measured step response, including the modulation enve-
lope, is shown in the Typical Performance Characteristics.
Choosing A = 0.5 is nearly optimal because it results in
monitor diode current. Recall that Imd_set is the digital set
point for the logarithm of the monitor diode current. This
fact has two important implications. First, the first order
temperature coefficient in Equation 23 (Imd_tc1) results
in an exponential change in the physical monitor diode
current with temperature. However, the monitor diode
temperature drift is usually very small, and the exponential
is well approximated as linear. Second, if Imd_tc2 = 0, the
relative temperature sensitivity of the physical current is
given by:
dI MD 1
smooth,exponentialsettling.A=1willsettleinabouttwo
servo iterations or 8ms, but “hunting” or low level oscil-
lation will be seen in the laser bias current. A > 1 results
?
dT I MD
= ln( 8 ) ? 2 – 13 ?Im d _ tc 1 ?
Im d _ nom
1024
(24)
in overshoot and A > 2 results in sustained high level
oscillation.
Imd_set
where I MD is the physical monitor diode current in Amps.
Equation 24 shows that the temperature coefficient of the
physical current depends on the nominal monitor diode
current. For example, if Imd_nom = 512 and Imd_tc1 = 4,
the physical temperature compensation would be:
Im_adc
dI MD 1
1
2
3
4
5
6
7
8
SERVO
ITERATIONS
?
dT I MD
= ln( 8 ) ? 2 – 13 ? 4 ?
512
1024
= 508 ppm / ° C (25)
0
4
8
12
16
20
24
28
32
TIME (ms)
5100 F25
The effect of Imd_tc2 on the physical monitor diode
current has no simple physical interpretation. In most
Figure 25. Step Response of the Monitor
Diode Current for a Total Loop Gain of 0.5
cases it will be sufficient to set Imd_tc2 to zero and use the
first order temperature coefficient, Imd_tc1 to correct
monitor diode drift.
Temperature Compensation
The set point value for the monitor diode current, Imd_set
in Figure 3, can be changed with temperature to compen-
sate the temperature dependence of the monitor diode
response. Temperature measurements are supplied either
by an on-chip temperature sensor or by an external
LASER BIAS CURRENT CONTROL IN CCC MODE
Figure 4 is a functional diagram of the LTC5100 operating
in constant current control (CCC) mode. In CCC mode, the
LTC5100 sets the laser bias current directly. Setting
Apc_en = 0 selects this mode. In CCC mode the laser bias
sn5100 5100fs
25
相关PDF资料 |
PDF描述 |
|---|---|
| AMC19DRTH-S734 | CONN EDGECARD 38POS DIP .100 SLD |
| T86D476M010EAAL | CAP TANT 47UF 10V 20% 2917 |
| VE-240-CX-F4 | CONVERTER MOD DC/DC 5V 75W |
| TACL105K010XTA | CAP TANT 1UF 10V 10% 0603 |
| T86D476K010EAAL | CAP TANT 47UF 10V 10% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC5100EUF#PBF | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC5100EUF#TR | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC5100EUF#TRPBF | 功能描述:IC DRIVER VCSEL 3.2GBPS 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 激光驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:60 系列:- 类型:激光二极管驱动器 数据速率:- 通道数:4 电源电压:3.3V 电流 - 电源:- 电流 - 调制:- 电流 - 偏置:- 工作温度:0°C ~ 70°C 封装/外壳:40-TQFN 裸露焊盘 供应商设备封装:40-TQFN EP 包装:托盘 安装类型:表面贴装 |
| LTC511P | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LTC5336E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
发布紧急采购，3分钟左右您将得到回复。