- 您现在的位置：买卖IC网 > PDF目录296348 > M29F400BB90MT3E (NUMONYX) 256K X 16 FLASH 5V PROM, 70 ns, PDSO44 PDF资料下载
参数资料
| 型号： | M29F400BB90MT3E |
| 厂商： | NUMONYX |
| 元件分类： | PROM |
| 英文描述： | 256K X 16 FLASH 5V PROM, 70 ns, PDSO44 |
| 封装： | 0.500 INCH, LEAD FREE, PLASTIC, SOP-44 |
| 文件页数： | 3/40页 |
| 文件大小： | 316K |
| 代理商： | M29F400BB90MT3E |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
M29F400BT, M29F400BB
Signal descriptions
2.7
Write Enable (W)
The Write Enable, W, controls the Bus Write operation of the memory’s Command Interface.
2.8
Reset/Block Temporary Unprotect (RP)
The Reset/Block Temporary Unprotect pin can be used to apply a Hardware Reset to the
memory or to temporarily unprotect all Blocks that have been protected.
A Hardware Reset is achieved by holding Reset/Block Temporary Unprotect Low, VIL, for at
least tPLPX. After Reset/Block Temporary Unprotect goes High, VIH, the memory will be
ready for Bus Read and Bus Write operations after tPHEL or tRHEL, whichever occurs last.
See the Ready/Busy Output section, Table Table 15. and Figure Figure 11.,
Reset/Temporary Unprotect AC Characteristics for more details.
Holding RP at VID will temporarily unprotect the protected Blocks in the memory. Program
and Erase operations on all blocks will be possible. The transition from VIH to VID must be
slower than tPHPHH.
2.9
Ready/Busy output (RB)
The Ready/Busy pin is an open-drain output that can be used to identify when the memory
array can be read. Ready/Busy is high-impedance during Read mode, Auto Select mode
and Erase Suspend mode.
After a Hardware Reset, Bus Read and Bus Write operations cannot begin until Ready/Busy
becomes high-impedance. See Table Table 15. and Figure Figure 11., Reset/Temporary
Unprotect AC Characteristics.
During Program or Erase operations Ready/Busy is Low, VOL. Ready/Busy will remain Low
during Read/Reset commands or Hardware Resets until the memory is ready to enter Read
mode.
The use of an open-drain output allows the Ready/Busy pins from several memories to be
connected to a single pull-up resistor. A Low will then indicate that one, or more, of the
memories is busy.
2.10
Byte/Word organization select (BYTE)
The Byte/Word Organization Select pin is used to switch between the 8-bit and 16-bit Bus
modes of the memory. When Byte/Word Organization Select is Low, VIL, the memory is in 8-
bit mode, when it is High, VIH, the memory is in 16-bit mode.
相关PDF资料 |
PDF描述 |
|---|---|
| M29F400BT70MT6T | 256K X 16 FLASH 5V PROM, 70 ns, PDSO44 |
| M29F800DB70N3F | 512K X 16 FLASH 5V PROM, 70 ns, PDSO48 |
| M29F800DB90N6T | 512K X 16 FLASH 5V PROM, 70 ns, PDSO48 |
| M29W160BT90ZA6 | 1M X 16 FLASH 2.7V PROM, 90 ns, PBGA48 |
| M29W400BT70M6T | 256K X 16 FLASH 2.7V PROM, 70 ns, PDSO44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M29F400BB90N1 | 功能描述:闪存 512Kx8 or 256Kx16 90 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| M29F400BB90N1T | 功能描述:闪存 512Kx8 or 256Kx16 90 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| M29F400BB90N6 | 功能描述:闪存 512Kx8 or 256Kx16 90 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| M29F400BB90N6T | 功能描述:闪存 512Kx8 or 256Kx16 90 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| M29F400BT45N1 | 功能描述:闪存 512Kx8 or 256Kx16 45 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。