收藏本站
参数资料
型号： M34584EDFP
元件分类： 微控制器/微处理器
英文描述： 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42
封装： 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42
文件页数： 93/157页
文件大小： 1130K
代理商： M34584EDFP
Rev.3.00
2004.08.06
page 40 of 155
REJ03B0010-0300Z
4584 Group
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
(11) Timer input/output pin
(D6/CNTR0 pin, C/CNTR1 pin)
CNTR0 pin is used to input the timer 1 count source and output the
timer 1 and timer 2 underflow signal divided by 2.
CNTR1 pin is used to input the timer 3 count source and output the
PWM signal generated by timer 4.
When the PWM signal is output from C/CNTR1 pin, set the output
latch of port C to “0”.
The D6/CNTR0 pin function can be selected by bit 0 of register W6.
The selection of CNTR1 output signal can be controlled by bit 3 of
register W4.
When the CNTR0 input is selected for timer 1 count source, timer
1 counts the rising or falling waveform of CNTR0 input. The count
edge is selected by the bit 2 of register W6.
When the CNTR1 input is selected for timer 3 count source, timer
3 counts the rising or falling waveform of CNTR1 input. The count
edge is selected by the bit 3 of register W6.
When CNTR1 input is selected, the output of port C is invalid (high-
impedance).
(12) PWM output function (C/CNTR1, timer 3,
timer 4)
When bit 3 of register W4 is set to “1”, timer 4 reloads data from re-
load register R4L and R4H alternately each underflow.
Timer 4 generates the PWM signal (PWMOUT) of the “L” interval
set as reload register R4L, and the “H” interval set as reload regis-
ter R4H. The PWM signal (PWMOUT) is output from CNTR1 pin.
When bit 2 of register W4 is set to “1” at this time, the interval
(PWM signal “H” interval) set to reload register R4H for the counter
of timer 4 is extended for a half period of count source.
In this case, when a value set in reload register R4H is n, timer 4
divides the count source signal by n + 1.5 (n = 1 to 255).
When this function is used, set “1” or more to reload register R4H.
When bit 1 of register W6 is set to “1”, the PWM signal output to
CNTR1 pin is switched to valid/invalid each timer 3 underflow.
However, when timer 3 is stopped (bit 2 of register W3 is cleared to
“0”), this function is canceled.
Even when bit 1 of a register W4 is cleared to “0” in the “H” interval
of PWM signal, timer 4 does not stop until it next timer 4 underflow.
When clearing bit 1 of register W4 to “0” to stop timer 4 at the use
of PWM output function, avoid a timing when timer 4 underflows.
(9) Count start synchronization circuit (timer 1,
timer 3)
Timer 1 and timer 3 have the count start synchronous circuit which
synchronizes the input of INT0 pin and INT1 pin, and can start the
timer count operation.
Timer 1 count start synchronous circuit function is selected by set-
ting the bit 0 of register I1 to “1” and the control by INT0 pin input
can be performed.
Timer 3 count start synchronous circuit function is selected by set-
ting the bit 0 of register I2 to “1” and the control by INT1 pin input
can be performed.
When timer 1 or timer 3 count start synchronous circuit is used, the
count start synchronous circuit is set, the count source is input to
each timer by inputting valid waveform to INT0 pin or INT1 pin.
The valid waveform of INT0 pin or INT1 pin to set the count start
synchronous circuit is the same as the external interrupt activated
condition.
Once set, the count start synchronous circuit is cleared by clearing
the bit I10 or I20 to “0” or reset.
However, when the count auto-stop circuit is selected, the count
start synchronous circuit is cleared (auto-stop) at the timer 1 or
timer 3 underflow.
(10) Count auto-stop circuit (timer 1, timer 3)
Timer 1 has the count auto-stop circuit which is used to stop timer
1 automatically by the timer 1 underflow when the count start syn-
chronous circuit is used.
The count auto-stop cicuit is valid by setting the bit 3 of register W1
to “1”. It is cleared by the timer 1 underflow and the count source to
timer 1 is stopped.
This function is valid only when the timer 1 count start synchronous
circuit is selected.
Timer 3 has the count auto-stop circuit which is used to stop timer
3 automatically by the timer 3 underflow when the count start syn-
chronous circuit is used.
The count auto-stop cicuit is valid by setting the bit 3 of register W3
to “1”. It is cleared by the timer 3 underflow and the count source to
timer 3 is stopped.
This function is valid only when the timer 3 count start synchronous
circuit is selected.
相关PDF资料
PDF描述
M35047-XXXSP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20
M35047-XXXFP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35048-001FP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35049-XXXFP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35053-XXXFP 24 X 10 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
相关代理商/技术参数
参数描述
M34584MD-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3459 功能描述:电缆固定件和配件 RLTCG 3/8 NPT GRAY NO NUT RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度:
M3460 功能描述:电缆固定件和配件 RLTCG 3/4 NPT BLACK NO NUT RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度:
M3460-3R9-083 制造商:Bonitron 功能描述:REGULATOR FOR VFDS
M3460B-E130-R2-DDM-P3 制造商:Bonitron 功能描述:UNDERVOLTAGE RIDE-THRU PRODUCT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*