- 您现在的位置：买卖IC网 > PDF目录80428 > M37531E4FP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO36 PDF资料下载
参数资料
| 型号： | M37531E4FP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| 封装： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-36 |
| 文件页数： | 38/216页 |
| 文件大小： | 1400K |
| 代理商： | M37531E4FP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页
5
5-15
INTERRUPT CONTROLLER (ICU)
32182 Group User’s Manual (Rev.1.0)
5.5.2 Processing by Internal Peripheral I/O Interrupt Handlers
(1) Branching to the interrupt handler
Upon accepting an interrupt request, the CPU branches to the EIT vector entry after performing the hardware
preprocessing as described in Section 4.3, “EIT Processing Procedure.” The EIT vector entry for External
Interrupt (EI) is located at the address H’0000 0080. This address is where the instruction (not the jump
address itself) for branching to the beginning of the interrupt handler routine for external interrupt requests is
written.
(2) Processing in the External Interrupt (EI) handler
A typical operation of the External Interrupt (EI) handler (for interrupts from internal peripheral I/O) is shown
in Figure 5.5.2.
[1] Saving each register to the stack
Save the BPC, PSW and general-purpose registers to the stack. Also, save the accumulator and FPSR
register to the stack as necessary.
[2] Reading the Interrupt Request Mask Register (IMASK) and saving to the stack
Read the Interrupt Request Mask Register and save its content to the stack.
[3] Reading the Interrupt Vector Register (IVECT)
Read the Interrupt Vector Register. This register holds the 16 low-order address bits of the ICU vector table
for the accepted interrupt request source that was stored in it when accepting an interrupt request. When the
Interrupt Vector Register is read, the following processing is automatically performed in hardware:
The interrupt priority level of the accepted interrupt request (ILEVEL) is set in the IMASK register as a
new IMASK value. (Interrupts with lower priority levels than that of the accepted interrupt request
source are masked.)
The accepted interrupt request source is cleared (not cleared for level-recognized interrupt request
sources).
The interrupt request (EI) to the CPU core is dropped.
The ICU’s internal sequencer is activated to start internal processing (interrupt priority resolution).
[4] Reading and overwriting the Interrupt Request Mask Register (IMASK)
Read the Interrupt Request Mask Register and overwrite it with the read value. This write to the IMASK
register causes the following processing to be automatically performed in hardware:
The interrupt request (EI) to the CPU core is dropped.
The ICU’s internal sequencer is activated to start internal processing (interrupt priority resolution).
Note: Processing in [4] here is unnecessary when multiple interrupts are to be enabled in [6] below.
[5] Reading the ICU vector table
Read the ICU vector table for the accepted interrupt request source. The relevant ICU vector table
address can be obtained by zero-extending the content of the Interrupt Vector Register that was read in
[3] (i.e., the 16 low-order address bits of the ICU vector table for the accepted interrupt request source).
The ICU vector table must have set in it the start address of the interrupt handler for the interrupt request
source concerned.)
[6] Enabling multiple interrupts
To enable another higher priority interrupt while processing the accepted interrupt (i.e., enabling multiple
interrupts), set the PSW register IE bit to "1".
[7] Branching to the internal peripheral I/O interrupt handler
Branch to the start address of the interrupt handler that was read out in [5].
[8] Processing in the internal peripheral I/O interrupt handler
[9] Disabling interrupts
Clear the PSW register IE bit to "0" to disable interrupts.
5.5 Description of Interrupt Operation
相关PDF资料 |
PDF描述 |
|---|---|
| M38507F8SP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M38027E8-XXXSP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP64 |
| M38044M4-XXXHP | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M38049FFHP | 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| M37540M2T-XXXFP | 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37531E4FP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MITSUBISHI 8 BIT OTP MCU |
| M37531E4GP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E4SP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E8FP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37531E8SP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。