- 您现在的位置：买卖IC网 > PDF目录67774 > M38C29FFAFP 8-BIT, FLASH, 5 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | M38C29FFAFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 5 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64 |
| 文件页数： | 5/104页 |
| 文件大小： | 1327K |
| 代理商： | M38C29FFAFP |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
Rev.2.00
May 28, 2004
page 100 of 100
38C2 Group (A Version)
Notes on Reset Circuit
1. Reset input voltage control
Make sure that the reset input voltage is less than 0.2 Vcc for Vcc(min).
2. Countermeasures for reset signal slow rising
In case where the RESET signal rise time is long, connect a ceramic
capacitor or others across the RESET pin and the Vss pin. Use a
1000 pF or more capacitor for high frequency use. When connecting
the capacitor, note the following:
Make the length of the wiring which is connected to a capacitor as
short as possible.
Be sure to verify the operation of application products on the user
side.
<Reason>
If the several nanosecond or several ten nanosecond impulse noise
enters the RESET pin, it may cause a microcomputer failure.
3. Port state immediately after reset
Table 1 shows the each pin state during RESET pin is “ L” .
Table 1 Each pin state during RESET pin is “ L”
Pin name
P0– P2 (SEG0– SEG23)
P3, P4, P5, P60– P62
COM0–COM3
Pin state
Input mode (with pull-up)
Input mode (high-impedance)
Vcc level input
4. Frequency relation of f(XIN) and f(
φ)
The frequency relation of f(XIN) and f(
φ) is f(XIN) = 8 f(φ).
Notes on Reset Circuit
1. Mode transition
(1) Both the main clock (XIN-XOUT) and sub-clock (XCIN-XCOUT) need
time for the oscillations to stabilize. The mode transition between
middle-/high-speed and low-speed mode must be performed af-
ter the corresponding clock becomes stable. The sub-clock, needs
extra time to stabilize particularly when executing operations af-
ter power-on and stop mode. The main and sub clocks require
the following condition for mode transition.
f(XIN) > 3 f(XCIN)
(2) The all modes can be switched to the stop mode or the wait mode
and return to the source mode when the stop mode or the wait
mode is ended.
2. State transitions of system clock
When the mode is switched from frequency/2/4/8 to the low-speed
mode, or the opposite is performed, change CM7 (bit 7 of system
clock control bits of CPU mode register (address 003B16)) at first,
and then, change CM6 (bit 6 of system clock control bits of CPU
mode register (address 003B16)) after the oscillation of the changed
mode is stabilized.
3. Wait mode
Timer and LCD operate in the wait mode.
Notes on Oscillation External Output Function
When the signal from the XOUT pin or XCOUT pin of the oscillation
circuit is input directly to the circuit except this MCU and used, the
system operation may be unstabilized.
In order to share the oscillation circuit safely, use the clock output
from P40 and P41 by the oscillation external output function for the
circuits except this MCU.
NOTES ON HARDWARE
Handling of Source Pins
In order to avoid a latch-up occurrence, connect a capacitor suitable
for high frequencies as bypass capacitor between power source pin
(VCC pin) and GND pin (VSS pin). Besides, connect the capacitor to
as close as possible. For bypass capacitor which should not be lo-
cated too far from the pins to be connected, a ceramic capacitor of
0.01
F– 0.1F is recommended.
相关PDF资料 |
PDF描述 |
|---|---|
| M38K29F8LHP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
| M38K27M4L-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64 |
| M38K29RFS | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, CPGA100 |
| M41ST85YMH6 | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| M41ST85YMX6TR | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38C29FFAFP#U0 | 功能描述:IC 740/38C2 MCU FLASH 64LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 产品培训模块:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 标准包装:1 系列:M16C™ M32C/80/87 核心处理器:M32C/80 芯体尺寸:16/32-位 速度:32MHz 连通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外围设备:DMA，POR，PWM，WDT 输入/输出数:121 程序存储器容量:384KB（384K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:24K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 34x10b，D/A 2x8b 振荡器型:内部 工作温度:-20°C ~ 85°C 封装/外壳:144-LQFP 包装:托盘 产品目录页面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M38C29FFAHP | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 60K 64-LQFP - Trays |
| M38C29FFAHP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 60KB FLASH 5V 64LQFP - Trays |
| M38C29FFFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C29FFHP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。