- 您现在的位置：买卖IC网 > PDF目录80396 > M41T81M6E (STMICROELECTRONICS) 1 TIMER(S), REAL TIME CLOCK, PDSO8 PDF资料下载
参数资料
| 型号： | M41T81M6E |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SOIC-8 |
| 文件页数： | 6/29页 |
| 文件大小： | 454K |
| 代理商： | M41T81M6E |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Clock operation
M41T81
Doc ID 7529 Rev 10
3.3
Calibrating the clock
The M41T81 is driven by a quartz controlled oscillator with a nominal frequency of
32,768 Hz. The devices are tested not exceed ±35 ppm (parts per million) oscillator
frequency error at 25oC, which equates to about +1.9 to –1.1 minutes per month (see
Figure 10 on page 15). When the calibration circuit is properly employed, accuracy improves
to better than ±2 ppm at 25°C.
The oscillation rate of crystals changes with temperature. The M41T81 design employs
periodic counter correction. The calibration circuit adds or subtracts counts from the
oscillator divider circuit at the divide by 256 stage, as shown in Figure 11 on page 15. The
number of times pulses which are blanked (subtracted, negative calibration) or split (added,
positive calibration) depends upon the value loaded into the five calibration bits found in the
control register. Adding counts speeds the clock up, subtracting counts slows the clock
down.
The calibration bits occupy the five lower order bits (D4-D0) in the control register 08h.
These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is a
sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs
within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one
second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is
loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a
binary 6 is loaded, the first 12 will be affected, and so on.
Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator
cycles for every 125,829,120 actual oscillator cycles, that is +4.068 or –2.034 ppm of
adjustment per calibration step in the calibration register (see Figure 11 on page 15).
Assuming that the oscillator is running at exactly 32,768 Hz, each of the 31 increments in
the calibration byte would represent +10.7 or –5.35 seconds per month which corresponds
to a total range of +5.5 or –2.75 minutes per month.
Two methods are available for ascertaining how much calibration a given M41T81 may
require.
The first involves setting the clock, letting it run for a month and comparing it to a known
accurate reference and recording deviation over a fixed period of time. Calibration values,
including the number of seconds lost or gained in a given period, can be found in application
note AN934, “TIMEKEEPER calibration.” This allows the designer to give the end user the
ability to calibrate the clock as the environment requires, even if the final product is
packaged in a non-user serviceable enclosure. The designer could provide a simple utility
that accesses the calibration byte.
The second approach is better suited to a manufacturing environment, and involves the use
of the IRQ/FT/OUT/SQW pin. The pin will toggle at 512Hz, when the stop bit (ST, D7 of 01h)
is '0,' the frequency test bit (FT, D6 of 08h) is '1,' the alarm flag enable bit (AFE, D7 of 0Ah)
is '0,' and the square wave enable bit (SQWE, D6 of 0Ah) is '0' and the watchdog register
(09h = 0) is reset.
Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at
the test temperature. For example, a reading of 512.010124 Hz would indicate a +20 ppm
oscillator frequency error, requiring a –10 (XX001010) to be loaded into the calibration byte
for correction. Note that setting or changing the calibration byte does not affect the
frequency test output frequency.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC11F1VPU3 | 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC908MR8VP | 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PDIP28 |
| MC68HLC908QY4CP | 8-BIT, FLASH, 2 MHz, MICROCONTROLLER, PDIP16 |
| MC68HC705P6ACP | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP28 |
| MC908GR60AMFU | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M41T81M6F | 功能描述:实时时钟 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| M41T81M6F-CUT TAPE | 制造商:ST 功能描述:M41T Series 2 V Serial I2C Real Time Clock with Alarm - SOIC-8 |
| M41T81M6TR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Serial Access Real-Time Clock with Alarms |
| M41T81MX | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:SERIAL ACCESS RTC WITH ALARMS |
| M41T81MX6 | 功能描述:实时时钟 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。