- 您现在的位置：买卖IC网 > PDF目录229297 > M93C06-DS3TG (STMICROELECTRONICS) 16 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | M93C06-DS3TG |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | PROM |
| 英文描述： | 16 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| 封装： | 3 X 3 MM, LEAD FREE, TSSOP-8 |
| 文件页数： | 31/31页 |
| 文件大小： | 533K |
| 代理商： | M93C06-DS3TG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页
9/31
M93C86, M93C76, M93C66, M93C56, M93C46, M93C06
Erase
The Erase Byte or Word (ERASE) instruction sets
the bits of the addressed memory byte (or word) to
1. Once the address has been correctly decoded,
the falling edge of the Chip Select Input (S) starts
the self-timed Erase cycle. The completion of the
cycle can be detected by monitoring the Ready/
Busy line, as described in the READY/BUSY STA-
TUS section.
Write
For the Write Data to Memory (WRITE) instruction,
8 or 16 data bits follow the op-code and address
bits. These form the byte or word that is to be writ-
ten. As with the other bits, Serial Data Input (D) is
sampled on the rising edge of Serial Clock (C).
After the last data bit has been sampled, the Chip
Select Input (S) must be taken Low before the next
rising edge of Serial Clock (C). If Chip Select Input
(S) is brought Low before or after this specific time
frame, the self-timed programming cycle will not
be started, and the addressed location will not be
programmed. The completion of the cycle can be
detected by monitoring the Ready/Busy line, as
described later in this document.
Once the Write cycle has been started, it is inter-
nally self-timed (the external clock signal on Serial
Clock (C) may be stopped or left running after the
start of a Write cycle). The cycle is automatically
preceded by an Erase cycle, so it is unnecessary
to execute an explicit erase instruction before a
Write Data to Memory (WRITE) instruction.
Figure 5. ERASE, ERAL Sequences
AI00879B
S
ERASE
1 1
D
Q
ADDR
OP
CODE
1
BUSY
READY
CHECK
STATUS
S
ERASE
ALL
1
0
D
Q
OP
CODE
1
BUSY
READY
CHECK
STATUS
0
An
A0
Xn X0
ADDR
相关PDF资料 |
PDF描述 |
|---|---|
| M93C06-WDS7 | 16 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| MT2VDDT832UY-75XX | 8M X 32 DDR DRAM MODULE, 0.75 ns, DMA100 |
| MB84VD22183EA-85PBS | SPECIALTY MEMORY CIRCUIT, PBGA71 |
| MB84VD22184EA-90PBS | SPECIALTY MEMORY CIRCUIT, PBGA71 |
| M93C66-WMB3TP | 256 X 16 MICROWIRE BUS SERIAL EEPROM, DSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M93C06DW | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit, 1Kbit and 256bit 8-bit or 16-bit wide |
| M93C06MN | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit, 1Kbit and 256bit 8-bit or 16-bit wide |
| M93C06-MN6 | 功能描述:电可擦除可编程只读存储器 256 (32x8 or 16x16) RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| M93C06-MN6T | 功能描述:电可擦除可编程只读存储器 256 (32x8 or 16x16) RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| M93C06-WBN6 | 功能描述:电可擦除可编程只读存储器 256 (32x8 or 16x16) RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。