- 您现在的位置：买卖IC网 > PDF目录224185 > M95256-RDW6TG (STMICROELECTRONICS) 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | M95256-RDW6TG |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | PROM |
| 英文描述： | 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封装： | 0.169 INCH, ROHS COMPLIANT, TSSOP-8 |
| 文件页数： | 2/44页 |
| 文件大小： | 386K |
| 代理商： | M95256-RDW6TG |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Signal description
M95256, M95256-W, M95256-R
3.6
Write Protect (W)
The main purpose of this input signal is to freeze the size of the area of memory that is
protected against Write instructions (as specified by the values in the BP1 and BP0 bits of
the Status Register).
This pin must be driven either high or low, and must be stable during all write instructions.
3.7
VSS ground
VSS is the reference for the VCC supply voltage.
3.8
Supply voltage (VCC)
3.8.1
Operating supply voltage VCC
Prior to selecting the memory and issuing instructions to it, a valid and stable VCC voltage
Table 9.). This voltage must remain stable and valid until the end of the transmission of the
instruction and, for a Write instruction, until the completion of the internal write cycle (tW). In
order to secure a stable DC supply voltage, it is recommended to decouple the VCC line with
a suitable capacitor (usually of the order of 10 nF to 100 nF) close to the VCC/VSS package
pins.
3.8.2
Power-up conditions
When the power supply is turned on, VCC continuously rises from VSS to VCC. During this
time, the Chip Select (S) line is not allowed to float but should follow the VCC voltage, it is
therefore recommended to connect the S line to VCC via a suitable pull-up resistor (see
In addition, the Chip Select (S) input offers a built-in safety feature, as the S input is edge-
sensitive as well as level-sensitive: after power-up, the device does not become selected
until a falling edge has first been detected on Chip Select (S). This ensures that Chip Select
(S) must have been high, prior to going low to start the first operation.
The VCC rise time must not vary faster than 1 V/s.
When VCC passes over the POR threshold, the device is reset and enters the Standby
Power mode. However, the device must not be accessed until VCC reaches a valid and
stable VCC voltage within the specified [VCC(min), VCC(max)] range.
3.8.3
Device Reset
In order to prevent inadvertent write operations during power-up (continuous rise in VCC), a
power on reset (POR) circuit is included. At power-up, the device does not respond to any
instruction until VCC has reached the power on reset threshold voltage (this threshold is
When VCC passes over the POR threshold, the device is reset and enters the following
state:
●
Standby Power mode
相关PDF资料 |
PDF描述 |
|---|---|
| MA-306-29.4912M-K0 | QUARTZ CRYSTAL RESONATOR, 29.4912 MHz |
| MA04206 | 2-PORT SAW RESONATOR, 433.92 MHz |
| MA05199 | 1-PORT SAW RESONATOR, 434.42 MHz |
| MA1050 | 1 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, SIP7 |
| MA21D35 | 1 A, 30 V, SILICON, SIGNAL DIODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M95256-RDW6TG/A | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit Serial SPI bus EEPROM with high speed clock |
| M95256-RDW6TG/K | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit serial SPI bus EEPROM with high-speed clock |
| M95256-RDW6TG/V | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit Serial SPI bus EEPROM with high speed clock |
| M95256RDW6TP | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit serial SPI bus EEPROM with high-speed clock |
| M95256-RDW6TP | 功能描述:电可擦除可编程只读存储器 256 Kbit Serial Bus 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。