- 您现在的位置：买卖IC网 > PDF目录224185 > M95256-RDW6TG (STMICROELECTRONICS) 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | M95256-RDW6TG |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | PROM |
| 英文描述： | 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封装： | 0.169 INCH, ROHS COMPLIANT, TSSOP-8 |
| 文件页数： | 44/44页 |
| 文件大小： | 386K |
| 代理商： | M95256-RDW6TG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页
M95256, M95256-W, M95256-R
Signal description
3
Signal description
See Figure 1: Logic diagram and Table 1: Signal names, for a brief overview of the signals
connected to this device.
3.1
Serial Data output (Q)
This output signal is used to transfer data serially out of the device. Data is shifted out on the
falling edge of Serial Clock (C).
3.2
Serial Data input (D)
This input signal is used to transfer data serially into the device. It receives instructions,
addresses, and the data to be written. Values are latched on the rising edge of Serial Clock
(C).
3.3
Serial Clock (C)
This input signal provides the timing of the serial interface. Instructions, addresses, or data
present at Serial Data input (D) are latched on the rising edge of Serial Clock (C). Data on
Serial Data output (Q) changes after the falling edge of Serial Clock (C).
3.4
Chip Select (S)
When this input signal is high, the device is deselected and Serial Data output (Q) is at high
impedance. Unless an internal Write cycle is in progress, the device will be in the Standby
Power mode. Driving Chip Select (S) low selects the device, placing it in the Active Power
mode.
After power-up, a falling edge on Chip Select (S) is required prior to the start of any
instruction.
3.5
Hold (HOLD)
The Hold (HOLD) signal is used to pause any serial communications with the device without
deselecting the device.
During the Hold condition, the Serial Data output (Q) is high impedance, and Serial Data
input (D) and Serial Clock (C) are Don’t Care.
To start the Hold condition, the device must be selected, with Chip Select (S) driven low.
相关PDF资料 |
PDF描述 |
|---|---|
| MA-306-29.4912M-K0 | QUARTZ CRYSTAL RESONATOR, 29.4912 MHz |
| MA04206 | 2-PORT SAW RESONATOR, 433.92 MHz |
| MA05199 | 1-PORT SAW RESONATOR, 434.42 MHz |
| MA1050 | 1 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, SIP7 |
| MA21D35 | 1 A, 30 V, SILICON, SIGNAL DIODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M95256-RDW6TG/A | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit Serial SPI bus EEPROM with high speed clock |
| M95256-RDW6TG/K | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit serial SPI bus EEPROM with high-speed clock |
| M95256-RDW6TG/V | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit Serial SPI bus EEPROM with high speed clock |
| M95256RDW6TP | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:256 Kbit serial SPI bus EEPROM with high-speed clock |
| M95256-RDW6TP | 功能描述:电可擦除可编程只读存储器 256 Kbit Serial Bus 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。