- 您现在的位置：买卖IC网 > Datasheet目录470 > MAX11014BGTM+T (Maxim Integrated)IC RF MESFET AMP 48-TQFN-EP Datasheet资料下载
参数资料
| 型号： | MAX11014BGTM+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 16/70页 |
| 文件大小： | 0K |
| 描述： | IC RF MESFET AMP 48-TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | RF MESFET 放大器漏极电流控制器 |
| RF 型： | 手机 |
| 次要属性： | 12 位 DAC 控制器 MESFET 栅极电压 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
Automatic RF MESFET Amplifier
Drain-Current Controllers
Detailed Description
The MAX11014/MAX11015 set and monitor the bias con-
ditions for dual MESFET power devices found in cellular
base stations and point-to-point microwave links. The
internal DAC sets the voltage across the current-sense
resistor by controlling the GATE voltage. These devices
integrate a 12-bit ADC to measure voltage, internal and
external temperature, and communicate through a 4-wire
20MHz SPI-/MICROWIRE-compatible serial interface or
2-wire 3.4MHz I 2 C-compatible serial interface
(pin-selectable).
The MAX11014/MAX11015 operate from an internal
+2.5V reference or individual ADC and DAC external
references. The external current-sense resistors moni-
tor voltages over the 0 to (V DACREF / 4) range. Two cur-
rent-sense amplifiers with a preset gain of four monitor
the voltage across the sense resistors. The
MAX11014/MAX11015 accurately measure their inter-
nal die temperature and two external remote diode tem-
perature sensors. The remote pn junctions are typically
the base-emitter junction of an npn transistor, either
discrete or integrated on a CPU, FPGA, or ASIC.
The MAX11014/MAX11015 also feature an ALARM out-
put that can be triggered during an internal or external
overtemperature condition, an excessive current-sense
voltage, or an excessive GATE voltage. Figure 4 shows
the MAX11014’s functional diagram.
The MAX11014 integrates complete dual analog
closed-loop drain-current controllers for Class A
MESFET amplifier operation. See the MAX11014 Class
A Control Loop section. The analog control loop sets
the drain current through the current-sense resistors.
The MESFET gate-drive amplifier can vary the DAC
code accordingly if the temperature or other system
variables change.
Implement Class A amplifier operation with the follow-
ing three steps:
1) Characterization
Characterize the MESFET over temperature to deter-
mine the amplifier ’s set of drain-current values,
assuming the part-to-part calibration curve is consis-
tent. There may be an offset shift, but no important
change in the shape of the function. Load these val-
ues into the MAX11014 LUTs at power-up. In opera-
tion, there is a linear interpolation between the
values stored in the LUTs.
Adjust the drain current for other variables such as
output power or drain voltage by loading values into
the numerical KLUTs.
2) Calibration
In production of the power amplifier, measure the
quiescent drain current at a fixed calibration temper-
ature (probably room) and adjust the V SET(CODE)
value until the drain current is within the specified
limits for that temperature. The V SET(CODE) value is
stored for loading after power-up. Prior to operation,
command a PGA calibration after powering up by
writing to the PGA calibration control register, setting
the TRACK bit to 0 and the DOCAL bit to 1 (see
Table 18).
3) Operation
Upon request, the MAX11014 measures the temper-
ature of the MESFET and compares it with the previ-
ous reading. If the temperature reading has
changed, the MAX11014 reads the LUTs with the
characterization data and updates the DAC to cor-
rect the drain current. Setting the TRACK, DOCAL,
and SELFTIME bits to 1 in the PGA calibration con-
trol register starts automatic monitoring and adjust-
ment of drain current for variations in temperature.
Also, if the KLUTs are used, their values are monitored
for changes. A DAC correction is then made if necessary.
For Class AB operation with the MAX11015, measure
the MESFET temperature and set the GATE_ voltage
through the LUTs and DAC to control the drain current.
See the MAX11015 Class AB Control section.
Implement Class AB amplifier operation with the same
three steps as Class A operation, with the exception
that the LUTs set the GATE_ voltage for constant drain
current with varying temperature.
Power-On Reset
On power-up, the MAX11014/MAX11015 are in full
power-down mode (see the SHUT (Write) section). To
change to normal power mode, write two commands to
the shutdown register. Set the FULLPD bit to 0 (other
bits in the shutdown register are ignored) on the first
command. A second command to this register then
activates the internal blocks.
MAX11014 Class A Control Loop
The MAX11014 is designed to set and continuously
control the drain current for MESFET power amplifiers
configured to operate in Class A. Set the DAC code to
control the voltage across the RCS_+ and RCS_- cur-
rent-sense resistor connections. The MAX11014 inter-
nal control loop automatically keeps the voltage across
the current-sense resistor to the value set by the DAC.
See the 12-Bit DAC section.
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX12000ETB+T | IC AMP GPS FRONT 1575MHZ 10TDFN |
| MAX12005ETM+T | IC SATELLITE IF SWITCH 48-TQFN |
| MAX1385BUTM+ | IC RF LDMOS BIAS CNTRLR 48-TQFN |
| MAX1470EUI+T | IC RECEIVER 315MHZ 28-TSSOP |
| MAX1470EVKIT-315 | EVAL KIT FOR MAX1470 315MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11014EVKIT+ | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX11014 - Bulk |
| MAX11015 | 功能描述:射频放大器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX11015BGTM | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
| MAX11015BGTM+ | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
| MAX11017 | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。