- 您现在的位置：买卖IC网 > Datasheet目录470 > MAX11014BGTM+T (Maxim Integrated)IC RF MESFET AMP 48-TQFN-EP Datasheet资料下载
参数资料
| 型号： | MAX11014BGTM+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 9/70页 |
| 文件大小： | 0K |
| 描述： | IC RF MESFET AMP 48-TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | RF MESFET 放大器漏极电流控制器 |
| RF 型： | 手机 |
| 次要属性： | 12 位 DAC 控制器 MESFET 栅极电压 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
Automatic RF MESFET Amplifier
Drain-Current Controllers
MISCELLANEOUS TIMING CHARACTERISTICS (continued)
Note 1: All current-sense amplifier specifications are tested after a current-sense calibration (valid when drain current = 0mA). See
RCS Error vs. GATE Current in the Typical Operating Characteristics. The calibration is valid only at one temperature and
supply voltage and must be repeated if either the temperature or supply voltage changes.
Note 2: The hardware configuration register’s CH_OCM1 and CH_OCM0 bits are set to 0. See Table 10a. The max specification is
limited by tester limitations.
Note 3: Guaranteed by design. Not production tested.
Note 4: At power-on reset, the output safe switch is closed. See the ALMHCFG (Read/Write) section.
Note 5: Integral nonlinearity is the deviation of the analog value at any code from its theoretical value after the gain and offset errors
have been calibrated out.
Note 6: Offset nulled.
Note 7: Absolute range for analog inputs is from 0 to V AVDD .
Note 8: Device and sensor at the same temperature. Verified by the current ratio (see the Temperature Measurements section).
Note 9: All timing specifications referred to V IH or V IL levels.
Note 10: D OUT goes into tri-state mode after the CS rising edge. Keep CS low long enough for the DOUT value to be sampled
before it goes to tri-state.
Note 11: A master device must provide a hold time of at least 300ns for the SDA signal (referred to V IL of the SCL signal) to bridge
the undefined region of SCL’s falling edge.
Note 12: t R and t F measured between 0.3 x DV DD and 0.7 x DV DD .
Note 13: C B = total capacitance of one bus line in pF. For bus loads between 100pF and 400pF, the timing parameters should be
linearly interpolated.
Note 14: An appropriate bus pullup resistance must be selected depending on board capacitance. For more information, refer to the
I 2 C documentation on the Philips website.
Note 15: Input filters on the SDA and SCL inputs suppress noise spikes less than 50ns.
Note 16: When a command is written to the serial interface, it is passed to the internal oscillator clock to be executed. There is a
small synchronization delay before the new value is written to the appropriate register. If the user attempts to read the new
value back before t RDBK , no harm will be caused to the data, but the read command may not yet show the new value.
Note 17: This is the minimum time from the end of a command before CNVST should be asserted. The time allows for the data from
the preceding write to arrive and set up the chip in preparation for the CNVST . The time need only be observed when the
write affects the ADC controls. Failure to observe this time may lead to incorrect conversions (for example, conversion of
the wrong ADC channel).
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX12000ETB+T | IC AMP GPS FRONT 1575MHZ 10TDFN |
| MAX12005ETM+T | IC SATELLITE IF SWITCH 48-TQFN |
| MAX1385BUTM+ | IC RF LDMOS BIAS CNTRLR 48-TQFN |
| MAX1470EUI+T | IC RECEIVER 315MHZ 28-TSSOP |
| MAX1470EVKIT-315 | EVAL KIT FOR MAX1470 315MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11014EVKIT+ | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX11014 - Bulk |
| MAX11015 | 功能描述:射频放大器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX11015BGTM | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
| MAX11015BGTM+ | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
| MAX11017 | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。