- 您现在的位置：买卖IC网 > PDF目录9899 > MAX1300BEUG+T (Maxim Integrated Products)IC ADC 16BIT SPI/SRL 24TSSOP PDF资料下载
参数资料
| 型号： | MAX1300BEUG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/31页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT SPI/SRL 24TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 16 |
| 采样率（每秒）： | 115k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 976mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极；8 个单端，双极；4 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
MAX1300/MAX1301
Unipolar Offset Error
-FSR to 0V
When a zero-scale analog input voltage is applied to
the converter inputs, the digital output is all ones
(0xFFFF). Ideally, the transition from 0xFFFF to 0xFFFE
occurs at AGND1 - 0.5 LSB. Unipolar offset error is the
amount of deviation between the measured zero-scale
transition point and the ideal zero-scale transition point,
with all untested channels grounded.
0V to +FSR
When a zero-scale analog input voltage is applied to
the converter inputs, the digital output is all zeros
(0x0000). Ideally, the transition from 0x0000 to 0x0001
occurs at AGND1 + 0.5 LSB. Unipolar offset error is the
amount of deviation between the measured zero-scale
transition point and the ideal zero-scale transition point,
with all untested channels grounded.
Bipolar Offset Error
When a zero-scale analog input voltage is applied to the
converter inputs, the digital output is a one followed by
all zeros (0x8000). Ideally, the transition from 0x7FFF to
0x8000 occurs at (2N-1 - 0.5)LSB. Bipolar offset error is
the amount of deviation between the measured midscale
transition point and the ideal midscale transition point,
with untested channels grounded.
Gain Error
When a positive full-scale voltage is applied to the con-
verter inputs, the digital output is all ones (0xFFFF). The
transition from 0xFFFE to 0xFFFF occurs at 1.5 LSB
below full scale. Gain error is the amount of deviation
between the measured full-scale transition point and
the ideal full-scale transition point with the offset error
removed and all untested channels grounded.
Unipolar Endpoint Overlap
Unipolar endpoint overlap is the change in offset when
switching between complementary input voltage
ranges. For example, the difference between the volt-
age that results in a 0xFFFF output in the -3 x VREF/2 to
0V input voltage range and the voltage that results in a
0x0000 output in the 0 to +3 x VREF/2 input voltage
range is the unipolar endpoint overlap. The unipolar
endpoint overlap is positive for the MAX1300/MAX1301,
preventing loss of signal or a dead zone when switch-
ing between adjacent analog input voltage ranges.
Small-Signal Bandwidth
A 100mVP-P sine wave is applied to the ADC, and the
input frequency is then swept up to the point where the
amplitude of the digitized conversion result has
decreased by -3dB.
Full-Power Bandwidth
A 95% of full-scale sine wave is applied to the ADC,
and the input frequency is then swept up to the point
where the amplitude of the digitized conversion result
has decreased by -3dB.
Common-Mode Rejection Ratio (CMRR)
CMRR is the ability of a device to reject a signal that is
“common” to or applied to both input terminals. The
common-mode signal can be either an AC or a DC sig-
nal or a combination of the two. CMR is expressed in
decibels. Common-mode rejection ratio is the ratio of
the differential signal gain to the common-mode signal
gain. CMRR applies only to differential operation.
Power-Supply Rejection Ratio (PSRR)
PSRR is the ratio of the output-voltage shift to the
power-supply-voltage shift for a fixed input voltage. For
the MAX1300/MAX1301, AVDD1 can vary from 4.75V to
5.25V. PSRR is expressed in decibels and is calculated
using the following equation:
For the MAX1300/MAX1301, PSRR is tested in bipolar
operation with the analog inputs grounded.
Aperture Jitter
Aperture jitter, tAJ, is the statistical distribution of the
variation in the sampling instant (Figure 21).
Aperture Delay
Aperture delay, tAD, is the time from the falling edge of
SCLK to the sampling instant (Figure 21).
Signal-to-Noise Ratio (SNR)
SNR is computed by taking the ratio of the RMS signal
to the RMS noise. RMS noise includes all spectral com-
ponents to the Nyquist frequency excluding the funda-
mental, the first five harmonics, and the DC offset.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to the RMS noise plus distortion. RMS noise plus
distortion includes all spectral components to the
Nyquist frequency excluding the fundamental and the
DC offset.
SINAD dB
Signal
Noise
RMS
(
)
log
=×
20
PSRR dB
VV
OUT
[
]
log
.
(.
)
(.
)
=×
20
525
4 75
525
4 75
8- and 4-Channel, ±3 x VREF Multirange Inputs,
Serial 16-Bit ADCs
28
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MS27499E22B35PA | CONN RCPT 100POS BOX MNT W/PINS |
| D38999/24MD19PA | CONN RCPT 19POS JAM NUT W/PINS |
| PT02SE-22-55S | CONN RECEPT 55POS W/SOCKET CRIMP |
| ISL32274EIVZ | IC XMITTER ESD RS422 LP 16-TSSOP |
| MS3111F14-5PY | CONN RCPT 5POS CBL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1300EVKIT+ | 功能描述:数据转换 IC 开发工具 MAX1300 Eval Kit RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX13013EBT | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX13013EBT+T | 功能描述:转换 - 电压电平 RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX13013EBT-T | 功能描述:转换 - 电压电平 RoHS:否 制造商:Micrel 类型:CML/LVDS/LVPECL to LVCMOS/LVTTL 传播延迟时间:1.9 ns 电源电流:14 mA 电源电压-最大:3.6 V 电源电压-最小:3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MLF-8 |
| MAX13013EXT | 制造商:Maxim Integrated Products 功能描述:+1.2V TO 3.6V 0.1MICROAMPS 100MBP - Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。