- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16031ETM+T (Maxim Integrated Products)IC SYSTEM MON EEPROM 48-TQFN PDF资料下载
参数资料
| 型号： | MAX16031ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/41页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MON EEPROM 48-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 8 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
EEPROM-Based System Monitors
with Nonvolatile Fault Memory
Detailed Description
Getting Started
The MAX16031/MAX16032 contain both I 2 C/SMBus and
JTAG serial interfaces for accessing registers and
EEPROM. Use only one interface at any given time. For
more information on how to access the internal memory
through these interfaces, see the I 2 C/SMBus-Compatible
Serial Interface and JTAG Serial Interface sections. This
data sheet uses a specific convention for referring to bits
within a particular address location. As an example,
r15h[3:0] refers to bits 3 through 0 in register with
address 15 hexadecimal.
The factory-default values at power-on reset (POR) for all
EEPROM locations are zeros. POR occurs when V CC
reaches the undervoltage lockout (UVLO) of 2.8V. At
POR, the device begins a boot-up sequence. During the
boot-up sequence, all monitored inputs are masked from
initiating faults and EEPROM contents are copied to the
respective register locations. The boot-up sequence
takes up to 1.81ms. Monitoring is disabled for up to 16s
past the boot-up sequence by programming r5Bh[3:0]
(see the Miscellaneous Settings section). RESET is low
during boot-up and remains low after boot-up for its pro-
grammed timeout period after all monitored channels are
within their respective thresholds.
The MAX16031/MAX16032 monitor up to eight voltages,
up to one current, and up to three temperatures. After
boot-up, an internal multiplexer cycles through each
input. At each multiplexer stop, the 10-bit ADC converts
the analog parameter to a digital result and stores the
result in a register. Each time the multiplexer completes a
cycle, internal logic compares the conversion results to
the thresholds stored in memory. When a conversion vio-
Table 2. Input Monitor Ranges and Enables
lates a programmed threshold, the conversion is config-
ured to generate a fault. Logic outputs are programmed
to depend on many combinations of faults. Additionally,
faults are programmed to trigger a fault log, whereby all
fault information is automatically written to EEPROM.
Voltage Monitoring
The MAX16031 provides eight inputs, IN1–IN8, for volt-
age monitoring. The MAX16032 provides six inputs,
IN1 –IN6, for voltage monitoring. Each input voltage
range is programmable through r17h[7:0] and r18h[7:0]
(see Table 2). Voltage monitoring for each input is
enabled through r1Ah[7:0] (see Table 2). There are four
programmable thresholds per voltage monitor input: pri-
mary undervoltage, secondary undervoltage, primary
overvoltage, and secondary overvoltage. All voltage
thresholds are 8 bits wide. Only the 8 most significant
bits of the conversion result are compared to the
thresholds. See the Miscellaneous Settings section to
set the amount of hysteresis for the thresholds. See
Table 1 for an address map of all voltage monitor input
threshold registers.
ADC inputs are configurable for two different modes:
pseudo-differential and single-ended (see Table 3). In
pseudo-differential mode, two inputs make up a differ-
ential pair. Psuedo-differential conversions are per-
formed by taking a single-ended conversion at each
input of a differential pair and then subtracting the
results. The pseudo-differential mode is selectable for
unipolar or bipolar operation. Unipolar differential oper-
ation allows only positive polarities of differential volt-
ages. Bipolar differential operation allows negative and
positive polarities of differential voltages. Bipolar con-
versions are in two’s complement format. For example,
REGISTER
ADDRESS
EEPROM
MEMORY
ADDRESS
BIT RANGE
DESCRIPTION
IN1 Voltage Range Selection:
[1:0]
[3:2]
00 = 5.6V, 01 = 2.8V
10 = 1.4V, 11 = Reserved
IN2 Voltage Range Selection:
00 = 5.6V, 01 = 2.8V
17h
97h
[5:4]
[7:6]
10 = 1.4V, 11 = Reserved
IN3 Voltage Range Selection:
00 = 5.6V, 01 = 2.8V
10 = 1.4V, 11 = Reserved
IN4 Voltage Range Selection:
00 = 5.6V, 01 = 2.8V
10 = 1.4V, 11 = Reserved
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16040PLA31+T | IC BATTERY BACKUP 3.08V 8-UDFN |
| MAX16043TG+T | IC SUPERVISOR CIRC QUAD 24TQFN |
| MAX16046ATN+ | IC EE-PROG SYS MGR 12CH 56-TQFN |
| MAX16047ETN+ | IC EE-PROG SYS MGR 12CH 56-TQFN |
| MAX16051ETI+T | IC POWER MONITR/SEQUENCER 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16031EVKIT+ | 功能描述:电源管理IC开发工具 MAX16031 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX16032ETM+ | 功能描述:监控电路 EEPROM-Based w/NV Fault Memory RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16032ETM+T | 功能描述:监控电路 EEPROM-Based w/NV Fault Memory RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16033LLB23+ | 制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR MONITOR 2.32V 10PIN UDFN - Rail/Tube |
| MAX16033LLB23+T | 功能描述:监控电路 Battery Backup 2.5V-Ep RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。