- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16031ETM+T (Maxim Integrated Products)IC SYSTEM MON EEPROM 48-TQFN PDF资料下载
参数资料
| 型号： | MAX16031ETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/41页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM MON EEPROM 48-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 8 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
EEPROM-Based System Monitors
with Nonvolatile Fault Memory
ABP
Table 5. Temperature Data Format
TEMPERATURE (°C)
+128
DIGITAL CODE
1100000000
DXP_
I LOW
I HIGH
+125
+100
+25.5
1011111010
1011010000
1000110011
DXN_
V BIAS ~ 100mV
ABP
I BIAS
-
+
TO ADC MUX
0
-10
-75
-100
-128
Diode fault
1000000000
0111101100
0101101010
0100111000
0100000000
0000000000
Reading ADC Results
Figure 4. Remote Temperature Sensor Amplifier Circuitry
The ADC converts the internal sensor and remote sen-
sor amplifier outputs. Each time the ADC converts all
enabled parameters, the temperature conversions are
compared to the temperature threshold registers (r46h
to r4Bh and r4Dh). Unlike the voltage input compara-
tors, the temperature threshold comparators are 10 bits
wide. OVERT is the designated output for temperature
faults, although other outputs are programmed to
depend on temperature faults as well. See the
Programmable Inputs/Outputs section for more informa-
tion on programming output dependencies. See the
Faults section for more information on setting tempera-
ture fault thresholds.
The remote temperature sensor amplifier detects a
short or open between DXP_ and DXN_. The detection
of these events is programmed to cause a fault.
Temperature thresholds and conversions are in a two’s
complement temperature format, where 1 LSB corre-
sponds to 0.5°C. The data format for temperature con-
versions is illustrated in Table 5.
Offset and gain errors for remote temperature sensor
measurements are user-trimmed through gain registers
r19h[7:2]/r4Fh[5:0] and offset registers r1Bh[7:5]/r4Dh[6:4],
as shown in Tables 4 and 6. The gain value trims the
high (56μA) drive current source to compensate for the
n-factor of the remote diode. The offset value is multi-
plied by 4 and added to the conversion result numeri-
cally. The MAX16031/MAX16032 contain an internal
lowpass filter at DXN_ and DXP_ to reduce noise. See
the Miscellaneous Settings section for more information
on programming the filter cutoff frequency.
ADC conversion results are read from the ADC conver-
sion registers through the I 2 C/SMBus-compatible or
JTAG interfaces (see Table 7). These registers are also
used for fault threshold comparison. Voltage monitoring
thresholds are compared with only the first 8 MSBs of
the conversion results.
Programmable Inputs/Outputs
The MAX16031 provides two general fault outputs,
FAULT1 and FAULT2 , one reset output RESET , one
temperature fault output OVERT , one current fault out-
put OVERC , two general-purpose inputs/outputs GPIO1
and GPIO2, and one SMBALERT#-compatible output
ALERT . The MAX16032 provides the same except
OVERC . All outputs are open drain and require pullup
resistors. Fault outputs do not latch except for OVERC ,
which either latches or does not latch depending on the
configuration bit in r5Ch. Individual fault flag bits, how-
ever, latch (see the Faults section) and must be cleared
one bit at a time by writing a byte containing all zeros
except for a single ‘1’ in the bit to be cleared.
The general outputs, FAULT1 and FAULT2 , are identi-
cal in functionality and are programmed to depend on
overvoltage, undervoltage, overtemperature, and over-
current parameters. See r1Dh and r1Eh in Table 8 for
more detailed information regarding the general fault
output dependencies.
The reset output RESET provides many programmable
output dependencies as well as reset timeouts. See
r20h and r21h in Table 8 for detailed information on
RESET output dependencies and timeouts.
The temperature fault output OVERT indicates tempera-
ture-related faults. OVERT is programmed to depend
on any primary temperature threshold and/or the
remote diode open/short flags. OVERT latches low dur-
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16040PLA31+T | IC BATTERY BACKUP 3.08V 8-UDFN |
| MAX16043TG+T | IC SUPERVISOR CIRC QUAD 24TQFN |
| MAX16046ATN+ | IC EE-PROG SYS MGR 12CH 56-TQFN |
| MAX16047ETN+ | IC EE-PROG SYS MGR 12CH 56-TQFN |
| MAX16051ETI+T | IC POWER MONITR/SEQUENCER 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16031EVKIT+ | 功能描述:电源管理IC开发工具 MAX16031 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX16032ETM+ | 功能描述:监控电路 EEPROM-Based w/NV Fault Memory RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16032ETM+T | 功能描述:监控电路 EEPROM-Based w/NV Fault Memory RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16033LLB23+ | 制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR MONITOR 2.32V 10PIN UDFN - Rail/Tube |
| MAX16033LLB23+T | 功能描述:监控电路 Battery Backup 2.5V-Ep RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。