- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16046ATN+ (Maxim Integrated Products)IC EE-PROG SYS MGR 12CH 56-TQFN PDF资料下载
参数资料
| 型号： | MAX16046ATN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/70页 |
| 文件大小： | 0K |
| 描述： | IC EE-PROG SYS MGR 12CH 56-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 37 |
| 类型： | 系统管理器 |
| 监视电压数目： | 12 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
MAX16046/MAX16048
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
Enable
To initiate sequencing/tracking and enable monitoring,
the voltage at EN must be above 0.525V and the
Software Enable bit in r4Dh[0] must be set to ‘0.’ To
power down and disable monitoring, either pull EN
below 0.5V or set the Software Enable bit to ‘1.’ See
If a fault condition occurs during the power-up cycle,
the EN_OUT_ outputs are powered down immediately,
independent of the state of EN. If operating in latch-on
fault mode, toggle EN or toggle the Software Enable bit
to clear the latch condition and restart the device once
the fault condition has been removed.
Table 1 for the software enable bit configurations.
Connect EN to ABP if not used.
Table 1. EEPROM Software Enable Configurations
REGISTER/
EEPROM ADDRESS
BIT RANGE
0
1
DESCRIPTION
Software Enable bit
0 = Enabled. EN must also be high to begin sequencing.
1 = Disabled (factory default)
Margin bit
1 = Margin functionality is enabled
0 = Margin disabled
4Dh
2
3
[7:4]
Early Warning Selection bit
0 = Early warning thresholds are undervoltage thresholds
1 = Early warning thresholds are overvoltage thresholds
Watchdog Mode Selection bit
0 = Watchdog timer is in dependent mode
1 = Watchdog timer is in independent mode
Not used
Voltage Monitoring
The MAX16046/MAX16048 feature an internal 10-bit
ADC that monitors the MON_ voltage inputs. An internal
multiplexer cycles through each of the twelve inputs,
taking 100μs (typ) for a complete monitoring cycle.
Each acquisition takes approximately 8.3μs. At each
multiplexer stop, the 10-bit ADC converts the analog
input to a digital result and stores the result in a regis-
ter. ADC conversion results are stored in registers r00h
to r17h in the extended page. Use the I 2 C or JTAG seri-
al interface to read ADC conversion results. See the
I 2 C/SMBus-Compatible Serial Interface or the JTAG
Serial Interface section for more information on access-
ing the extended page.
The MAX16046 provides twelve inputs, MON1–MON12,
for voltage monitoring. The MAX16048 provides eight
inputs, MON1 –MON8, for voltage monitoring. Each
input voltage range is programmable in registers r0Fh
to r11h (see Table 2). When MON_ configuration
18
registers are set to ‘11,’ MON_ voltages are not moni-
tored or converted, and the multiplexer does not stop at
these inputs, decreasing the total cycle time. These
inputs cannot be configured to trigger fault conditions.
The three programmable thresholds for each monitored
voltage include an overvoltage, an undervoltage, and
an early warning threshold that can be set in r4Dh[2] to
be either an undervoltage or overvoltage threshold. See
the Faults section for more information on setting over-
voltage and undervoltage thresholds. All voltage
thresholds are 8 bits wide. The 8 MSBs of the 10-bit
ADC conversion result are compared to these overvolt-
age and undervoltage thresholds.
For any undervoltage or overvoltage condition to be
monitored and any faults detected, the MON_ input
must be assigned to a particular sequence order. See
the Sequencing section for more details on assigning
MON_ inputs.
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16047ETN+ | IC EE-PROG SYS MGR 12CH 56-TQFN |
| MAX16051ETI+T | IC POWER MONITR/SEQUENCER 28TQFN |
| MAX16055AAUB+ | IC MPU SUPERVISOR HEX 10MSOP |
| MAX16058ATA46+T | IC SUPERVISOR OD 4.6V 8-TDFN |
| MAX1605EUT-T | IC REG BOOST ADJ 0.5A SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16046ATN+ | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16046ATN+T | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16046ECB+ | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16046ECB+T | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16046ETN+ | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。