- 您现在的位置：买卖IC网 > PDF目录1837 > MAX16046ATN+ (Maxim Integrated Products)IC EE-PROG SYS MGR 12CH 56-TQFN PDF资料下载
参数资料
| 型号： | MAX16046ATN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 34/70页 |
| 文件大小： | 0K |
| 描述： | IC EE-PROG SYS MGR 12CH 56-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 37 |
| 类型： | 系统管理器 |
| 监视电压数目： | 12 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
MAX16046/MAX16048
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
Closed-Loop Tracking
The MAX16046/MAX16048 track up to four voltages
during any time slot except Slot 0 and Slot 12.
Configure GPIO1–GPIO4 as sense line inputs (INS_) to
monitor tracking voltages. Configure GPIO6 as
FAULTPU to indicate tracking faults, if desired. See the
General-Purpose Inputs/Outputs section for information
on configuring GPIOs.
For closed-loop tracking, use MON1, EN_OUT1, and
INS1 together to form a complete channel. Use MON2,
EN_OUT2, and INS2 to form a second complete chan-
nel. Use MON3, EN_OUT3, and INS3 together to form a
third channel. Use MON4, EN_OUT4, and INS4 to form
a fourth channel.
When configured for closed-loop tracking, assign each
EN_OUT_ to the same slot as its associated single
monitoring input (MON_). For example, if EN_OUT2 is
assigned to Slot 3, the monitoring input is MON2 and
must be assigned to Slot 3. This is because the MON_
input, checked at the start of the slot, must be valid
before tracking can begin. Tracking begins immediate-
ly and must finish before the power-up fault timeout
expires, or a fault will trigger. EN_OUT_ configured for
closed-loop tracking cannot be assigned to Slot 0.
The tracking control circuitry includes a ramp generator
and a comparator control block for each tracked volt-
age (see the Functional Diagram and Figure 5). The
comparator control block compares each INS_ voltage
Power-down initiates when EN is forced low or when
the Software Enable bit in r4Dh[0] is set to ‘1.’ If the
Reverse Sequence bit is set (r54h[4]) INS_ voltages fol-
low a falling reference ramp to ground as long as
MON_ voltages remain high enough to supply the
required voltage/current. If a monitored voltage drops
faster than the control ramp voltage or the correspond-
ing MON_ voltage falls too quickly, power-down track-
ing operation is terminated and all EN_OUT_ voltages
are immediately forced to ground. If the Reverse
Sequence bit is set to ‘0,’ all EN_OUT_ voltages are
forced low simultaneously.
The MAX16046/MAX16048 include selectable internal
100 Ω pulldown resistors to ensure that tracked voltages
are not held high by large external capacitors during a
fault event. The pulldowns help to ensure that monitored
INS_ voltages are fully discharged before the next power-
up cycle is initiated. These pulldowns are high imped-
ance during normal operation. Set r4Eh[7:4] to ‘1’ to
enable the pulldown resistors (Table 13). These pulldown
resistors may also be used with EN_OUT1–EN_OUT4
channels not configured for closed-loop tracking, which
is useful to discharge the output capacitors of a DC-DC
converter during shutdown. For this case, configure the
GPIO as an INS_ input and set the 100 Ω pulldown bit,
but do not enable closed-loop tracking. Connect the
INS_ input to the output of the power supply.
with a control voltage ramp. If INS_ voltages vary from
the control ramp by more than 150mV (typ), the com-
parator control block signals an alert that dynamically
V IN
V OUT
stops the ramp until the slow INS_ voltage rises to with-
in the allowed voltage window. The total tracking time is
extended under these conditions, but must still com-
plete within the selected power-up/power-down fault
MON_
ADC MUX
EN_OUT_
GATE
DRIVE
INS_
timeout. The power-up/power-down tracking fault time-
out period is adjustable through r4Eh[3:0].
LOGIC
A voltage difference between any two tracking INS_
voltages exceeding 330mV generates a tracking fault,
forcing all EN_OUT_ voltages low and generating a
fault log. If configured as FAULTPU , GPIO6 asserts
when a tracking fault occurs.
The comparator control blocks also monitor INS_ voltages
with respect to input (MON_) voltages. Under normal con-
ditions each INS_ tracks the control ramp until the INS_
voltages reach the configured power-good (PG) thresh-
olds, set as a programmable percentage of the MON_
voltage. Use register r64h to set the PG thresholds (Table
15). Once PG is detected, the external n-channel FET sat-
urates with 5V (typ) applied between gate and source.
The slew rate for the control ramp is programmable from
REFERENCE
RAMP
V TH_PG
100 Ω
100V/s to 800V/s in r4Fh[5:4] (see Table 13).
34
Figure 5. Closed-Loop Tracking
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16047ETN+ | IC EE-PROG SYS MGR 12CH 56-TQFN |
| MAX16051ETI+T | IC POWER MONITR/SEQUENCER 28TQFN |
| MAX16055AAUB+ | IC MPU SUPERVISOR HEX 10MSOP |
| MAX16058ATA46+T | IC SUPERVISOR OD 4.6V 8-TDFN |
| MAX1605EUT-T | IC REG BOOST ADJ 0.5A SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16046ATN+ | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16046ATN+T | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16046ECB+ | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16046ECB+T | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16046ETN+ | 功能描述:监控电路 12Ch EEPROM Prob System Manager RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。