- 您现在的位置：买卖IC网 > PDF目录1838 > MAX17003ETJ+T (Maxim Integrated Products)IC PS CTRLR FOR NOTEBOOKS 32TQFN PDF资料下载
参数资料
| 型号： | MAX17003ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/36页 |
| 文件大小： | 0K |
| 描述： | IC PS CTRLR FOR NOTEBOOKS 32TQFN |
| 标准包装： | 2,500 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 6 V ~ 26 V |
| 输出数： | 4 |
| 输出电压： | 3.3V，5V，2 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
Table 4. FSEL Configuration Table
Idle Mode Current-Sense Threshold
When pulse-skipping mode is enabled, the on-time of the
FSEL
LDO5
REF
GND
SWITCHING FREQUENCY (kHz)
500
300
200
step-down controller terminates when the output voltage
exceeds the feedback threshold and when the current-
sense voltage exceeds the idle-mode current-sense
threshold. Under light-load conditions, the on-time dura-
tion depends solely on the idle mode current-sense
Frequency Selection (FSEL)
The FSEL input selects the PWM mode switching fre-
quency. Table 4 shows the switching frequency based
on FSEL connection. High-frequency (500kHz) operation
optimizes the application for the smallest component
size, trading off efficiency due to higher switching losses.
This may be acceptable in ultraportable devices where
the load currents are lower. Low-frequency (200kHz)
operation offers the best overall efficiency at the expense
of component size and board space.
Forced-PWM Mode
The low-noise forced-PWM mode ( SKIP = LDO5) dis-
ables the zero-crossing comparator, which controls the
low-side switch on-time. This forces the low-side gate-
drive waveform to be constantly the complement of the
high-side gate-drive waveform, so the inductor current
reverses at light loads while DH_ maintains a duty factor
of V OUT /V IN . The benefit of forced-PWM mode is to keep
the switching frequency fairly constant. However, forced-
PWM operation comes at a cost: the no-load 5V supply
current remains between 20mA to 50mA, depending on
the external MOSFETs and switching frequency.
Forced-PWM mode is most useful for avoiding audio-
frequency noise and improving load-transient
response. Since forced-PWM operation disables the
zero-crossing comparator, the inductor current revers-
es under light loads.
Light-Load Operation Control ( SKIP )
The MAX17003/MAX17004 include a light-load operat-
threshold, which is 20% ( SKIP = GND) of the full-load
current-limit threshold set by ILIM, or the low-noise cur-
rent-sense threshold, which is 10% ( SKIP = REF) of the
full-load current-limit threshold set by ILIM. This forces
the controller to source a minimum amount of power with
each cycle. To avoid overcharging the output, another
on-time cannot begin until the output voltage drops
below the feedback threshold. Since the zero-crossing
comparator prevents the switching regulator from sinking
current, the controller must skip pulses. Therefore, the
controller regulates the valley of the output ripple under
light-load conditions.
Automatic Pulse-Skipping Crossover
In skip mode, an inherent automatic switchover to PFM
takes place at light loads (Figure 4). This switchover is
affected by a comparator that truncates the low-side
switch on-time at the inductor current’s zero crossing.
The zero-crossing comparator senses the inductor cur-
rent across CSH_ to CSL_. Once (V CSH _ - V CSL _)
drops below the 3mV zero-crossing, current-sense
threshold, the comparator forces DL_ low (Figure 3).
This mechanism causes the threshold between pulse-
skipping PFM and nonskipping PWM operation to coin-
cide with the boundary between continuous and
ing mode control input ( SKIP ) used to enable or dis-
able the zero-crossing comparator for both switching
regulators. When the zero-crossing comparator is
enabled, the regulator forces DL_ low when the cur-
rent-sense inputs detect zero inductor current. This
keeps the inductor from discharging the output capaci-
tors and forces the regulator to skip pulses under light-
load conditions to avoid overcharging the output. When
the zero-crossing comparator is disabled, the regulator
is forced to maintain PWM operation under light-load
conditions (forced-PWM).
0
t ON(SKIP) =
V OUT
V IN f OSC
TIME
I PK
I LOAD = I PK /2
ON-TIME
Figure 4. Pulse-Skipping/Discontinuous Crossover Point
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17005AETP+ | IC BATT CHARGER 1.2MHZ 20TQFN |
| MAX17005BETP+ | IC BATT CHARGER 1.2MHZ 20-TQFN |
| MAX17007GTI+T | IC CTRLR QPWM GRAPHICS 28TQFN |
| MAX1700EEE+T | IC REG BST SYNC ADJ 0.8A 16QSOP |
| MAX17010ETL+T | IC LCD DISPLAY BIAS 40-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17004AETJ+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX17004ETJ+ | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17004ETJ+T | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17005AETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005AETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。