- 您现在的位置：买卖IC网 > PDF目录1838 > MAX17003ETJ+T (Maxim Integrated Products)IC PS CTRLR FOR NOTEBOOKS 32TQFN PDF资料下载
参数资料
| 型号： | MAX17003ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/36页 |
| 文件大小： | 0K |
| 描述： | IC PS CTRLR FOR NOTEBOOKS 32TQFN |
| 标准包装： | 2,500 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 6 V ~ 26 V |
| 输出数： | 4 |
| 输出电压： | 3.3V，5V，2 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
Table 5. Operating Modes Truth Table
MODE
Power-Up
Run
Output Overvoltage
(OVP) Protection
(MAX17003)
Output Undervoltage
Protection (UVP)
Standby
Shutdown
Thermal Shutdown
Switchover Fault
CONDITION
LDO5 < UVLO threshold
SHDN = high, ON3 or ON5 enabled
Either output > 111% of nominal level
Either output < 70% of nominal level,
UVP is enabled 6144 clock cycles
(1/f OSC ) after the output is enabled
ON5 and ON3 < startup threshold,
SHDN = high
SHDN = low
T J > +160°C
Excessive current on LDO5 switchover
transistors
COMMENT
Transitions to discharge mode after V IN POR and after REF
becomes valid. LDO5, REF remain active. DL_ is low.
Normal operation.
Exited by POR or cycling SHDN , ON3, or ON5.
Exited by POR or cycling SHDN , ON3, or ON5.
DL_ stays low. LDO5 active.
All circuitry off.
Exited by POR or cycling SHDN , ON3, or ON5.
DL3 and DL5 go low before LDO5 turns off.
Exited by POR or cycling SHDN , ON3, or ON5.
ON3 or ON5 low). Once the soft-start sequence termi-
nates, PGDALL becomes high impedance as long as
both SMPS outputs are above 90% of the nominal regu-
lation voltage set by FB. PGDALL goes low once either
SMPS output drops 10% below its nominal regulation
point, an SMPS output overvoltage fault occurs, or ON_
or SHDN is low. For a logic-level PGDALL output volt-
age, connect an external pullup resistor between
PGDALL and LDO5. A 100k Ω pullup resistor works well
in most applications.
Fault Protection
Output Overvoltage Protection (OVP)—
MAX17003 Only
If the output voltage of either SMPS rises above 111% of
its nominal regulation voltage and the OVP protection is
enabled, the controller sets the fault latch, pulls
PGDALL low, shuts down the SMPS controllers that
tripped the fault, and immediately pulls DH_ low and
forces DL_ high. This turns on the synchronous-rectifier
MOSFETs with 100% duty, rapidly discharging the out-
put capacitors and clamping both outputs to ground.
However, immediately latching DL_ high typically caus-
es slightly negative output voltages due to the energy
stored in the output LC at the instant the OVP occurs. If
the load cannot tolerate a negative voltage, place a
power Schottky diode across the output to act as a
reverse-polarity clamp. If the condition that caused the
overvoltage persists (such as a shorted high-side MOS-
FET), the battery blows. The other output is shut down
using the soft-discharge feature with DL_ forced low.
Cycle LDO5 below 1V or toggle either ON3, ON5, or
SHDN to clear the fault latch and restart the SMPS con-
trollers.
Output Undervoltage Protection (UVP)
Each SMPS controller includes an output UVP protection
circuit that begins to monitor the output 6144 clock
cycles (1/f OSC ) after that output is enabled (ON_ pulled
high). If either SMPS output voltage drops below 70% of
its nominal regulation voltage and the UVP protection is
enabled, the UVP circuit sets the fault latch, pulls
PGDALL low, and shuts down both controllers using the
soft-discharge feature with DL_ forced low. Cycle LDO5
below 1V or toggle either ON3, ON5, or SHDN to clear
the fault latch and restart the SMPS controllers.
Thermal-Fault Protection
The MAX17003/MAX17004 feature a thermal fault-pro-
tection circuit. When the junction temperature rises
above +160 ° C, a thermal sensor activates the fault
latch, pulls PGDALL low, and shuts down both SMPS
controllers using the soft-discharge feature with DL_
forced low. Toggle either ON3, ON5, or SHDN to clear
the fault latch and restart the controllers after the junc-
tion temperature cools by 15 ° C.
24
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17005AETP+ | IC BATT CHARGER 1.2MHZ 20TQFN |
| MAX17005BETP+ | IC BATT CHARGER 1.2MHZ 20-TQFN |
| MAX17007GTI+T | IC CTRLR QPWM GRAPHICS 28TQFN |
| MAX1700EEE+T | IC REG BST SYNC ADJ 0.8A 16QSOP |
| MAX17010ETL+T | IC LCD DISPLAY BIAS 40-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17004AETJ+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX17004ETJ+ | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17004ETJ+T | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17005AETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005AETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。