- 您现在的位置：买卖IC网 > PDF目录1838 > MAX17003ETJ+T (Maxim Integrated Products)IC PS CTRLR FOR NOTEBOOKS 32TQFN PDF资料下载
参数资料
| 型号： | MAX17003ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 22/36页 |
| 文件大小： | 0K |
| 描述： | IC PS CTRLR FOR NOTEBOOKS 32TQFN |
| 标准包装： | 2,500 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 6 V ~ 26 V |
| 输出数： | 4 |
| 输出电压： | 3.3V，5V，2 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
discontinuous inductor-current operation (also known
as the “critical conduction” point). The load-current
level at which PFM/PWM crossover occurs, I LOAD(SKIP) ,
TO ERROR
AMPLIFIER
ADJUSTABLE
is given by:
FB
OUTPUT
I LOAD ( SKIP ) =
(V IN ? V OUT )V OUT
2 V IN f OSC L
LDO5
R
The switching waveforms may appear noisy and asyn-
chronous when light loading causes pulse-skipping
operation, but this is a normal operating condition that
9R
results in high light-load efficiency. Trade-offs in PFM
noise vs. light-load efficiency are made by varying the
inductor value. Generally, low inductor values produce
a broader efficiency vs. load curve, while higher values
result in higher full-load efficiency (assuming that the
coil resistance remains fixed) and less output-voltage
ripple. Drawbacks of using higher inductor values
OUT
FIXED OUTPUT
FB = LDO5
V OUT ( PWM ) = V NOM ? 1 ?
? ? ? ?
?
?
?
?
? V OUT _ ?
R FBHI FBLO ?
1 ? f SW ?
2 ? ? f OSC ? ?
include larger physical size and degraded load-tran-
sient response (especially at low input-voltage levels).
Output Voltage
DC output accuracy specifications in the Electrical
Characteristics table refer to the error comparator’s
threshold. When the inductor continuously conducts,
the MAX17003/MAX17004 regulate the peak of the out-
put ripple, so the actual DC output voltage is lower than
the slope-compensated trip level by 50% of the output
ripple voltage. For PWM operation (continuous conduc-
tion), the output voltage is accurately defined by the fol-
lowing equation:
? A SLOPE V RIPPLE ? ? V RIPPLE ?
V IN 2
where V NOM is the nominal output voltage, A SLOPE
equals 1%, and V RIPPLE is the output ripple voltage
(V RIPPLE = ESR x Δ I INDUCTOR , as described in the
Output Capacitor Selection section).
In discontinuous conduction (I OUT < I LOAD(SKIP) ), the
MAX17003/MAX17004 regulate the valley of the output
ripple, so the output voltage has a DC regulation level
higher than the error-comparator threshold. For PFM
operation (discontinuous conduction), the output volt-
age is approximately defined by the following equation:
V OUT ( PFM ) = V NOM + I IDLE ESR
where V NOM is the nominal output voltage, f OSC is the
maximum switching frequency set by the internal oscil-
lator, f SW is the actual switching frequency, and I IDLE is
the idle mode inductor current when pulse skipping .
Figure 5. Dual Mode Feedback Decoder
Connect FB3 and FB5 to LDO5 to enable the fixed
SMPS output voltages (3.3V and 5V, respectively), set
by a preset, internal resistive voltage-divider connected
between the output (CSL_) and analog ground.
Connect a resistive voltage-divider at FB_ between the
output (CSL_) and GND to adjust the respective output
voltage between 2V and 5.5V (Figure 5). Choose R FBLO
(resistance from FB to GND) to be approximately 10k Ω
and solve for R FBHI (resistance from the output to FB)
using the equation:
= R ? 1 ?
? V FB _ ?
where V FB_ = 2V nominal.
When adjusting both output voltages, set the 3.3V
SMPS lower than the 5V SMPS. LDO5 connects to the
5V output (CSL5) through an internal switch only when
CSL5 is above the LDO5 bootstrap threshold (4.5V)
and the soft-start sequence for the CSL5 side has com-
pleted. Bootstrapping works most effectively when the
fixed output voltages are used. Once LDO5 is boot-
strapped from CSL5, the internal 5V linear regulator
turns off. This reduces the internal power dissipation
and improves efficiency at higher input voltages.
Current-Limit Protection (ILIM)
The current-limit circuit uses differential current-sense
inputs (CSH_ and CSL_) to limit the peak inductor cur-
rent. If the magnitude of the current-sense signal
exceeds the current-limit threshold, the PWM controller
turns off the high-side MOSFET (Figure 3). The actual
22
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17005AETP+ | IC BATT CHARGER 1.2MHZ 20TQFN |
| MAX17005BETP+ | IC BATT CHARGER 1.2MHZ 20-TQFN |
| MAX17007GTI+T | IC CTRLR QPWM GRAPHICS 28TQFN |
| MAX1700EEE+T | IC REG BST SYNC ADJ 0.8A 16QSOP |
| MAX17010ETL+T | IC LCD DISPLAY BIAS 40-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17004AETJ+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX17004ETJ+ | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17004ETJ+T | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17005AETP+ | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17005AETP+T | 功能描述:电池管理 1.2MHz High-Perf Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。