- 您现在的位置：买卖IC网 > PDF目录5134 > MAX1904EAI+T (Maxim Integrated Products)IC CNTRLR PWR SPLY LN 28-SSOP PDF资料下载
参数资料
| 型号： | MAX1904EAI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/33页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR PWR SPLY LN 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 4.2 V ~ 30 V |
| 输出数： | 4 |
| 输出电压： | 2.5 V ~ 5 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
500kHz Multi-Output, Low-Noise Power-Supply
Controllers for Notebook Computers
Table 2. Component Suppliers
three signals: the output-voltage error signal with
respect to the reference voltage, the current-sense sig-
MANUFACTURER
Dale-Vishay
Fairchild
Semiconductor
International
Rectifier
Sanyo
Sumida
Taiyo Yuden
USA PHONE
402-564-3131
408-721-2181
310-322-3331
619-661-6835
847-956-0666
408-573-4150
FACTORY FAX
402-563-6418
408-721-1635
310-322-3332
619-661-1055
847-956-0702
408-573-4159
nal, and the slope-compensation ramp (Figure 3). The
PWM controller is a direct-summing type, lacking a tra-
ditional error amplifier and the phase shift associated
with it. This direct-summing configuration approaches
ideal cycle-by-cycle control over the output voltage.
When SKIP = low, Idle Mode circuitry automatically
optimizes efficiency throughout the load current range.
Idle Mode dramatically improves light-load efficiency
by reducing the effective frequency, which reduces
switching losses. It keeps the peak inductor current
above 25% of the full current limit in an active cycle,
allowing subsequent cycles to be skipped. Idle Mode
The MAX1901/MAX1902/MAX1904 contain ten major
circuit blocks (Figure 2).
The two pulse-width-modulation (PWM) controllers
each consist of a Dual Mode feedback network and
multiplexer, a multi-input PWM comparator, high-side
and low-side gate drivers, and logic. MAX1901/
MAX1902 contain fault-protection circuits that monitor
the main PWM outputs for undervoltage and overvolt-
age. A power-on sequence block controls the power-
up timing of the main PWMs and determines whether
one or both of the outputs are monitored for undervoltage
faults. The MAX1902 includes a secondary feedback net-
work and 12V linear regulator to generate a 12V output
from a coupled-inductor flyback winding. The
MAX1901/MAX1904 have a secondary feedback input
(SECFB) instead, which allows a quasi-regulated,
adjustable output, coupled-inductor flyback winding to be
attached to either the 3.3V or the 5V main inductor. Bias
generator blocks include the 5V IC internal rail (V L ) linear
regulator, 2.5V precision reference, and automatic boot-
strap switchover circuit. The PWMs share a common
333kHz/500kHz synchronizable oscillator.
These internal IC blocks aren ’ t powered directly from
the battery. Instead, the 5V V L linear regulator steps
down the battery voltage to supply both V L and the
gate drivers. The synchronous-switch gate drivers are
directly powered from V L , while the high-side switch
gate drivers are indirectly powered from V L via an
external diode-capacitor boost circuit. An automatic
bootstrap circuit turns off the 5V linear regulator and
powers the IC from the 5V PWM output voltage if the
output is above 4.5V.
PWM Controller Block
The two PWM controllers are nearly identical. The only
differences are fixed output settings (3.3V vs. 5V), the
VL/CSL5 bootstrap switch connected to the 5V PWM,
and SECFB. The heart of each current-mode PWM con-
troller is a multi-input, open-loop comparator that sums
transitions seamlessly to fixed-frequency PWM opera-
tion as load current increases.
With SKIP = high, the controller always operates in fixed-
frequency PWM mode for lowest noise. Each pulse from
the oscillator sets the main PWM latch that turns on the
high-side switch for a period determined by the duty fac-
tor (approximately V OUT / V IN ). As the high-side switch
turns off, the synchronous rectifier latch sets; 60ns later,
the low-side switch turns on. The low-side switch stays on
until the beginning of the next clock cycle.
In PWM mode, the controller operates as a fixed-fre-
quency current-mode controller where the duty ratio is
set by the input/output voltage ratio. The current-mode
feedback system regulates the peak inductor current
value as a function of the output-voltage error signal. In
continuous-conduction mode, the average inductor
current is nearly the same as the peak current, so the
circuit acts as a switch-mode transconductance ampli-
fier. This pushes the second output LC filter pole, nor-
mally found in a duty-factor-controlled (voltage-mode)
PWM, to a higher frequency. To preserve inner-loop
stability and eliminate regenerative inductor current
“ staircasing ” , a slope-compensation ramp is summed
into the main PWM comparator to make the apparent
duty factor less than 50%.
The MAX1901/MAX1902/MAX1904 use a relatively low
loop gain, allowing the use of lower-cost output capaci-
tors. The relative gains of the voltage-sense and cur-
rent-sense inputs are weighted by the values of current
sources that bias three differential input stages in the
main PWM comparator (Figure 4). The relative gain of
the voltage comparator to the current comparator is
internally fixed at K = 2:1. The low loop gain results in
the 2% typical load-regulation error. The low value of
loop gain helps reduce output filter capacitor size and
cost by shifting the unity-gain crossover frequency to a
lower level.
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1902EAI+T | IC CNTRLR PWR SPLY LN 28-SSOP |
| UPM1A561MPD6 | CAP ALUM 560UF 10V 20% RADIAL |
| UPM1A561MPD | CAP ALUM 560UF 10V 20% RADIAL |
| MAX1901EAI+T | IC CNTRLR PWR SPLY LN 28-SSOP |
| UPM1A471MPD6 | CAP ALUM 470UF 10V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1904EAI-TG074 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1904ETJ | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1904ETJ+ | 功能描述:DC/DC 开关控制器 500kHz Multi-Output Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1904ETJ+T | 功能描述:DC/DC 开关控制器 500kHz Multi-Output Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1904ETJ-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。