- 您现在的位置：买卖IC网 > PDF目录5134 > MAX1904EAI+T (Maxim Integrated Products)IC CNTRLR PWR SPLY LN 28-SSOP PDF资料下载
参数资料
| 型号： | MAX1904EAI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/33页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR PWR SPLY LN 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 4.2 V ~ 30 V |
| 输出数： | 4 |
| 输出电压： | 2.5 V ~ 5 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
500kHz Multi-Output, Low-Noise Power-Supply
Controllers for Notebook Computers
RESET Power-Good Voltage Monitor
The power-good monitor generates a system RESET
signal. At first power-up, RESET is held low until both
the 3.3V and 5V SMPS outputs are in regulation. At this
point, an internal timer begins counting oscillator puls-
es, and RESET continues to be held low until 32,000
cycles have elapsed. After this timeout period (64ms at
500kHz or 96ms at 333kHz), RESET is actively pulled
up to V L . If SEQ is tied to REF (for separate ON3/ON5
controls), only the 3.3V SMPS is monitored — the 5V
SMPS is ignored.
Output Undervoltage Shutdown
Protection (MAX1901/MAX1902)
The output undervoltage lockout circuit is similar to
foldback current limiting, but employs a timer rather
than a variable current limit. Each SMPS has an under-
voltage protection circuit that is activated 6144 clock
cycles after the SMPS is enabled. If either SMPS output
is under 70% of the nominal value, both SMPSs are
latched off and their outputs are clamped to ground by
the synchronous rectifier MOSFETs (see the Output
Overvoltage Protection section). They won ’ t restart until
SHDN or RUN/ON3 is toggled, or until V+ power is
cycled below 1V. Note that undervoltage protection can
make prototype troubleshooting difficult, since you
have only 12ms or 18ms to figure out what might be
wrong with the circuit before both SMPSs are latched
off. In extreme cases, it may be useful to substitute the
MAX1904 into the prototype breadboard until the proto-
type is working properly.
Output Overvoltage Protection
(MAX1901/MAX1902)
Both SMPS outputs are monitored for overvoltage. If
either output is more than 7% above the nominal regu-
lation point, both low-side gate drivers (DL_) are
latched high until SHDN or RUN/ON3 is toggled, or
until V+ power is cycled below 1V. This action turns on
the synchronous rectifiers with 100% duty, in turn rapid-
ly discharging the output capacitors and forcing both
SMPS outputs to ground. The DL outputs are also kept
high whenever the corresponding SMPS is disabled,
and in shutdown if V L is sustained.
Discharging the output capacitor through the main
inductor causes the output to momentarily go below
GND. Clamp this negative pulse with a back-biased 1A
Schottky diode across the output capacitor (Figure 1).
To ensure overvoltage protection on initial power-up,
connect signal diodes from both output voltages to V L
(cathodes to V L ) to eliminate the V L power-up delay.
This circuitry protects the load from accidental overvolt-
age caused by a short circuit across the high-side
power MOSFETs. This scheme relies on the presence
of a fuse, in series with the battery, which is blown by
the resulting crowbar current. Note that the overvoltage
circuitry will interfere with external keep-alive supplies
that hold up the outputs (such as lithium backup or hot-
swap power supplies); in such cases, the MAX1904
should be used.
Low-Noise Operation (PWM Mode)
PWM mode ( SKIP = high) minimizes RF and audio inter-
ference in noise-sensitive applications (such as hi-fi multi-
media-equipped systems), cellular phones, RF
communicating computers, and electromagnetic pen
entry systems. See the summary of operating modes in
Table 2. SKIP can be driven from an external logic signal.
Table 4. Operating Modes
SHDN
Low
High
High
High
High
High
High
High
High
SEQ
X
REF
REF
REF
REF
GND
GND
VL
VL
RUN/ON3
X
Low
High
Low
High
Low
High
Low
High
TIME/ON5
X
Low
Low
High
High
Timing Capacitor
Timing Capacitor
Timing Capacitor
Timing Capacitor
MODE
Shutdown
Standby
Run
Run
Run
Standby
Run
Standby
Run
DESCRIPTION
All circuit blocks turned off.
Supply current = 4μA.
Both SMPSs off. Supply current = 30μA.
3.3V SMPS enabled/5V off.
5V SMPS enabled/3.3V off.
Both SMPSs enabled.
Both SMPSs off. Supply current = 30μA.
Both SMPSs enabled. 5V enabled before 3.3V.
Both SMPSs off. Supply current = 30μA.
Both SMPSs enabled. 3.3V enabled Before 5V.
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1902EAI+T | IC CNTRLR PWR SPLY LN 28-SSOP |
| UPM1A561MPD6 | CAP ALUM 560UF 10V 20% RADIAL |
| UPM1A561MPD | CAP ALUM 560UF 10V 20% RADIAL |
| MAX1901EAI+T | IC CNTRLR PWR SPLY LN 28-SSOP |
| UPM1A471MPD6 | CAP ALUM 470UF 10V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1904EAI-TG074 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1904ETJ | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1904ETJ+ | 功能描述:DC/DC 开关控制器 500kHz Multi-Output Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1904ETJ+T | 功能描述:DC/DC 开关控制器 500kHz Multi-Output Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1904ETJ-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。