- 您现在的位置：买卖IC网 > PDF目录1841 > MAX1964TEEE+ (Maxim Integrated Products)IC POWER CTRLR/SEQUENCER 16QSOP PDF资料下载
参数资料
| 型号： | MAX1964TEEE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/30页 |
| 文件大小： | 0K |
| 描述： | IC POWER CTRLR/SEQUENCER 16QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 应用： | 电源控制器，序列发生器 |
| 输入电压： | 4.5 V ~ 28 V |
| 电流 - 电源： | 1.25mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Tracking/Sequencing Triple/Quintuple
Power-Supply Controllers
-I PEAK
I LOAD
I VALLEY
[
( ) ]
Figure 3. “ Valley ” Current-Limit Threshold Point
TIME
I PEAK = I VALLEY +
(V IN - V OUT )
L
V OUT
V IN ? OSC
The DL low-side drive waveform is always the comple-
ment of the DH high-side drive waveform (with con-
trolled dead time to prevent cross-conduction or
“ shoot-through ” ). A dead-time circuit monitors the DL
output and prevents the high-side FET from turning on
until DL is fully off. In order for the dead-time circuit to
work properly, there must be a low-resistance, low-
inductance path from the DL driver to the MOSFET
gate. Otherwise, the sense circuitry in the MAX1964/
MAX1965 will interpret the MOSFET gate as “ off ” when
gate charge actually remains. Use very short, wide
traces (50mils to 100mils wide if the MOSFET is 1 inch
from the device). The dead time at the other edge (DH
turning off) is determined by a fixed internal delay.
High-Side Gate-Drive Supply (BST)
Gate-drive voltage for the high-side N-channel switch is
generated by a flying-capacitor boost circuit (Figure 1).
The capacitor between BST and LX is alternately
charged from the VL supply and placed parallel to the
high-side MOSFET ’ s gate and source terminals.
On startup, the synchronous rectifier (low-side MOS-
FET) forces LX to ground and charges the boost
capacitor to 5V. On the second half-cycle, the switch-
mode power supply turns on the high-side MOSFET by
closing an internal switch between BST and DH. This
provides the necessary gate-to-source voltage to turn
on the high-side switch, an action that boosts the 5V
gate-drive signal above the input voltage.
Internal 5V Linear Regulator (VL)
All MAX1964/MAX1965 functions, except the current-
sense amplifier, are internally powered from the on-
chip, low-dropout 5V regulator. The maximum regulator
input voltage (V IN ) is 28V. Bypass the regulator ’ s output
(VL) with a ceramic capacitor of at least 1μF to GND.
The V IN -to-VL dropout voltage is typically 200mV, so
when V IN is less than 5.2V, VL is typically V IN - 200mV.
The internal linear regulator can source up to 20mA to
supply the IC, power the low-side gate driver, charge
the external boost capacitor, and supply small external
loads. When driving particularly large FETs, little or no
regulator current may be available for external loads.
For example, when switched at 200kHz, a large FET
with 40nC total gate charge requires 40nC x 200kHz, or
8mA.
Undervoltage Lockout
If VL drops below 3.5V, the MAX1964/MAX1965
assumes that the supply voltage is too low to make
valid decisions, so the undervoltage lockout (UVLO)
circuitry inhibits switching, forces POK low, and forces
the DL and DH gate drivers low. After VL rises above
3.5V, the controller powers up the outputs (see Startup
section).
Startup
Externally, the MAX1964/MAX1965 start switching when
VL rises above the 3.5V undervoltage lockout thresh-
old. However, the controller is not enabled unless all
four conditions are met: 1) VL exceeds the 3.5V under-
voltage lockout threshold, 2) the internal reference
exceeds 92% of its nominal value (V REF > 1.145V), 3)
the internal bias circuitry powers up, and 4) the thermal
limit is not exceeded. Once the MAX1964/MAX1965
assert the internal enable signal, the step-down con-
troller starts switching and enables soft-start.
The soft-start circuitry gradually ramps up to the refer-
ence voltage in order to control the rate of rise of the
step-down controller and reduce input surge currents
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1967EUB+T | IC REG CTRLR BUCK PWM VM 10-UMAX |
| MAX1969EUI+T | IC DRVR POWER 28-TSSOP |
| MAX1971EEE+T | IC REG BUCK SYNC 0.75A DL 16QSOP |
| MAX1973EUB+T | IC REG BUCK SYNC ADJ 1A 10UMAX |
| MAX1977EEI+ | IC CNTRLR PS QUAD HI EFF 28QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1964TEEE+ | 功能描述:电流和电力监控器、调节器 Track/Seq Trpl/Wuint Power-Supply Ctlr RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX1964TEEE+T | 功能描述:电流和电力监控器、调节器 Track/Seq Trpl/Wuint Power-Supply Ctlr RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX1964TEEE-T | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX1965TEEP | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX1965TEEP-T | 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。