参数资料
型号: MAX1964TEEE+
厂商: Maxim Integrated Products
文件页数: 24/30页
文件大小: 0K
描述: IC POWER CTRLR/SEQUENCER 16QSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 100
应用: 电源控制器,序列发生器
输入电压: 4.5 V ~ 28 V
电流 - 电源: 1.25mA
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 16-SSOP(0.154",3.90mm 宽)
供应商设备封装: 16-QSOP
包装: 管件
Tracking/Sequencing Triple/Quintuple
Power-Supply Controllers
V SUP
MAX1964
MAX1965
B_
C BE
R BE
Q PASS
C BYP
R1
V POS
FB_
R2
C LDO
a) POSITIVE OUTPUT VOLTAGE
R4
V REF
BF5
R3
V NEG
B5
Q PASS
C NEG
MAX1965
C BE
R BE
V SUP
Figure 7. Base-Drive Noise Reduction
b) NEGATIVE OUTPUT VOLTAGE (MAX1965 ONLY)
C BYP
2 π ? POLE ( CBE ) ?
? ? - C IN ( Q )
C BE ≤
1 ? R BE I LOAD + V T h FE ?
R BE V T h FE ?
where V SAT is the pass transistor ’ s saturation voltage
under full load. For negative output voltages (MAX1965
only), connect the transformer as shown in Figure 6
where the minimum turns ratio (N NEG = N S(NEG) /N P ) is
?
?
?
?
where C IN(Q) is the transistor ’ s input capacitance, and
f POLE(CBE) is the second pole required for stability.
Transformer Selection
In systems where the step-down controller ’ s output is
not the highest voltage, a transformer may be used to
provide additional post-regulated, high-voltage outputs.
The transformer generates unregulated, high-voltage
supplies which power the positive and negative linear
regulators. These unregulated supply voltages are
dependent on the transformer ’ s turns ratio – number of
secondary turns (N S ) divided by the number of primary
turns (N P ). So the transformer must be selected to pro-
vide supply voltages high enough to keep the pass
transistors from saturating. For positive output voltages,
connect the transformer as shown in Figure 6 where the
minimum turns ratio (N POS = N S(POS) /N P ) is determined
by:
determined by:
? V LDO ( NEG ) + V SAT + V DIODE ?
N NEG ≥ ? ?
V OUT
Since power transfer occurs when the low-side MOS-
FET is on (DL = high), the transformer cannot support
heavy loads with high duty cycles.
Snubber Design
The MAX1964/MAX1965 use current-mode control
schemes that sense the current across the high-side
MOSFET (N H ). Immediately after the high-side MOSFET
turns on, the MAX1964/MAX1965 use a 60ns current-
sense blanking period to minimize noise sensitivity.
However, when the MOSFET turns on, the transformer ’ s
secondary inductance and the diode ’ s parasitic capac-
N POS ≥ ?
-1 ?
? V LDO(POS) + V SAT + V DIODE
? V OUT
?
?
itance form a resonant circuit that causes ringing.
Reflected back through the transformer to the primary
side, these oscillations appear across the high-side
MOSFET may last longer than the blanking period. As
24
______________________________________________________________________________________
相关PDF资料
PDF描述
MAX1967EUB+T IC REG CTRLR BUCK PWM VM 10-UMAX
MAX1969EUI+T IC DRVR POWER 28-TSSOP
MAX1971EEE+T IC REG BUCK SYNC 0.75A DL 16QSOP
MAX1973EUB+T IC REG BUCK SYNC ADJ 1A 10UMAX
MAX1977EEI+ IC CNTRLR PS QUAD HI EFF 28QSOP
相关代理商/技术参数
参数描述
MAX1964TEEE+ 功能描述:电流和电力监控器、调节器 Track/Seq Trpl/Wuint Power-Supply Ctlr RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
MAX1964TEEE+T 功能描述:电流和电力监控器、调节器 Track/Seq Trpl/Wuint Power-Supply Ctlr RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
MAX1964TEEE-T 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
MAX1965TEEP 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
MAX1965TEEP-T 功能描述:电流和电力监控器、调节器 RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel