- 您现在的位置：买卖IC网 > PDF目录18777 > MAX2160ETL+ (Maxim Integrated)IC TUNER ISDB-T LOW IF 40TQFN PDF资料下载
参数资料
| 型号： | MAX2160ETL+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/25页 |
| 文件大小： | 0K |
| 描述： | IC TUNER ISDB-T LOW IF 40TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 系列： | * |
| 频率： | 470MHz ~ 770MHz |
| 应用： | 手机 |
| 电流 - 接收： | 44mA |
| 数据接口： | PCB，表面贴装 |
| 存储容量： | * |
| 天线连接器： | PCB，表面贴装 |
| 电源电压： | 2.7 V ~ 3.3 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 托盘 |
ISDB-T Single-Segment Low-IF Tuners
START
WRITE DEVICE
ADDRESS
R/W
ACK
READ FROM STATUS
BYTE-1 REGISTER
ACK
READ FROM STATUS
BYTE-2 REGISTER
ACK/
NACK
STOP
1100000
1
Figure 3. Example: Receive Data from Read Registers
Read Cycle
There are only two registers on the MAX2160/EBG that
are available to be read by the master. When
addressed with a read command, the MAX2160/EBG
send back the contents of both read registers (STATUS
BYTE-1 and STATUS BYTE-2).
A read cycle begins with the bus master issuing a
START condition followed by the seven slave address
bits and a read bit (R/ W = 1). If the slave address byte
is successfully received, the MAX2160/EBG issue an
ACK. The master then reads the contents of the STA-
TUS BYTE-1 register, beginning with the most signifi-
cant bit, and acknowledges if the byte is received
successfully. Next, the master reads the contents of the
STATUS BYTE-2 register. At this point the master can
issue an ACK or NACK and then a STOP condition to
terminate the read cycle.
Figure 3 illustrates an example in which the read regis-
ters are read by the master.
Applications Information
RF Input (RFIN)
The MAX2160/EBG are internally matched to 50 ? and
requires a DC-blocking capacitor (see the Typical
Operating Circuit ).
RF Gain Control (GC1)
The MAX2160/EBG feature a variable-gain low-noise
amplifier that provides 43dB of RF gain-control range.
The voltage control (V GC1 ) range is 0.3V (minimum
attenuation) to 2.7V (maximum attenuation).
IF Power Detector
The MAX2160/EBG include a true RMS power detector
at the mixer output. The power-detector circuit is
enabled or disabled with the EPD bit in the control reg-
ister. The attack point can be set through the PD[2:0]
bits in the control register (see Table 5 for a summary
of attack point settings).
The PWRDET pin output can be configured to provide
either a voltage output (directly from the RMS power-
detector stage) or current output (default) through the
diagnostic bits D[2:0] in the test register.
Closed-Loop RF Power Control
The default mode of the IF power detector is current out-
put mode. Closed-loop RF power control is formed by
connecting the PWRDET pin directly to the GC1 pin. A
shunt capacitor to ground is added to set the closed-
loop response time (see the Typical Operating Circuit ).
The recommended capacitor value of 10nF provides a
response time of 0.1ms.
Closed-loop RF power control can also be formed using
the baseband processor and the power detector in volt-
age output mode. In this configuration, the processor
senses the power detector’s output voltage and uses this
information to drive the GC1 pin directly. Voltage output
mode is enabled by setting the D[2:0] bits in the test reg-
ister to 100. In voltage mode, the PWRDET pin outputs a
scaled DC voltage proportional to the RF input power.
For the RF input range of -62dBm to -48dBm, the DC
output voltage ranges from 84mV to 420mV.
High-Side and Low-Side LO Injection
The MAX2160/EBG allow selection between high-side
and low-side LO injection through the HSLS bit in the
control register. High-side injection is the default setting
(HSLS = 1).
Q-Channel Shutdown
The Q channel low-IF output of the MAX2160/EBG can
be turned off with the QOFF bit in the XTAL divide reg-
ister for use with single low-IF input demodulators (use I
channel only). Turning off the Q channel reduces the
supply current by approximately 3mA.
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1471ATJ+ | IC RCVR ASK/FSK LP 32-TQFN |
| MICRF011BM | IC RCVR/DATA DEMOD RF/IF 14SOIC |
| AMB310908 | SENSOR REFL LONG H-TYPE |
| MICRF009BM | IC RECEIVER UHF LOW POWER 16SOIC |
| MICRF007BM | IC RECEIVER UHF LOW POWER 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2160ETL+ | 功能描述:调谐器 ISDB-T Single-Seg Low-IF Tuner RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX2160ETL+T | 功能描述:调谐器 ISDB-T Single-Seg Low-IF Tuner RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX2160ETL-T | 功能描述:调谐器 ISDB-T Single-Seg Low-IF Tuner RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX2160EVKIT | 功能描述:射频开发工具 MAX2160 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX2161E/W-B3N | 功能描述:调谐器 RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。