- 您现在的位置：买卖IC网 > PDF目录16545 > MAX5042ATN+T (Maxim Integrated Products)IC PWR W/MOSFET HS 56-TQFN PDF资料下载
参数资料
| 型号： | MAX5042ATN+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/22页 |
| 文件大小： | 0K |
| 描述： | IC PWR W/MOSFET HS 56-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 电源 |
| 电源电压： | 20 V ~ 76 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
| 包装： | 带卷 (TR) |
Two-Switch Power ICs with Integrated
Power MOSFETs and Hot-Swap Controller
Pin Description (continued)
MAX5042
47
PIN
MAX5043
25, 47
NAME
POSINPWM
FUNCTION
PWM Analog Positive-Supply Input. Connect POSINPWM to the most positive input
supply rail.
48, 51, 54, 55 48, 51, 54, 55
49, 50, 52, 53 49, 50, 52, 53
DRNH
XFRMRH
Drain Connection of the Internal High-Side PWM Power MOSFET. Connect DRNH to
the most positive rail of the input supply.
High-Side Connection for the Isolation Transformer
Delayed Enable Input (MAX5043 Only). DEN is the center point of the delayed
—
27
DEN
enable divider. Use an external voltage-divider or a 100k ? pullup resistor to the
most positive rail to override.
—
30
N.C.
No Connection (MAX5043 Only). Leave unconnected.
Detailed Description
+V POSINPWM
The MAX5042/MAX5043 PWM multimode power ICs
are designed for the primary side of voltage or current-
mode isolated, forward or flyback power converters.
MAX5042
QH
BULK STORAGE CAPACITOR
(HOT-SWAPPED CAPACITOR)
These devices provide a high degree of integration
aimed at reducing the cost and PC board area of isolat-
PWM
CIRCUIT
C IN
T1
L
V OUT
QL
ed output power supplies. Use the MAX5042/MAX5043
primarily for 24V, 42V, or 48V power bus applications.
The MAX5042/MAX5043 provide a complete system
capable of delivering up to 50W of output power. The
MAX5042 contains a hot-swap controller in addition to
the PWM and power MOSFETs. The hot-swap section
requires an external MOSFET (QHS). Figure 1 details
WITH
INTEGRATED
FETs
INTEGRATED
HOT-SWAP
CONTROLLER
QHS
PWMNEG, PWMPNEG
EXTERNAL
HOT-SWAP FET
C OUT
the MAX5042 conceptual block diagram. C IN represents
the input bulk storage capacitance of the PWM circuit
that requires the soft-start to reduce the inrush current
from the backplane. When input power is applied,
capacitor C IN is completely discharged and QHS is off.
An applied voltage higher than the default undervoltage
lockout threshold of the hot-swap controller (30.5V) for
more than 165ms (internal turn-on delay) causes the
gate voltage of QHS to start gradually increasing. This
results in a controlled slew-rate turn-on. The drain volt-
age of QHS falls at a rate of approximately 10V/ms,
drawing a current load from the backplane of approxi-
mately 1A for each 100μF of C IN capacitance. The
MAX5042’s PWM block is prevented from starting up
until the QHS MOSFET is fully enhanced. After QHS
completely turns on and the voltage across capacitor
C IN is above the default startup voltage (31V) of the
PWM section, the hot swap enables the PWM block and
the soft-start cycle begins. Soft-start limits the amount of
current initially drawn from the primary during startup
and also prevents possible output-voltage overshoots.
NEGIN
Figure 1. Simplified Diagram of a MAX5042-Based Isolated
Power Supply
The MAX5043, detailed in Figure 2, does not contain an
integrated hot-swap controller. The MAX5043 begins
operating when the input voltage exceeds both of the
undervoltage lockout voltages (at UVLO and DEN pins)
for 10ms.
The MAX5042/MAX5043 support both forward and fly-
back power topologies. In forward mode, the maximum
output power is approximately 50W. In flyback mode,
the maximum output power is approximately 20W. The
amount of power dissipated by the package limits the
output power. The MAX5042/MAX5043’s QFN package
features an exposed metal pad on the bottom of the
package. Solder the exposed pad directly to the most
negative supply in the system. Use a large copper area
to improve heat dissipation. Facilitate heat transfer with
thermal vias.
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| PX0441/2M00 | CABLE IP68 MINI B TO A USB 2M |
| BA6219BFP-YE2 | IC DRIVER MOTOR REVERSE HSOP25 |
| VI-J5Y-EZ-S | CONVERTER MOD DC/DC 3.3V 16.5W |
| VI-J5W-EZ-S | CONVERTER MOD DC/DC 5.5V 25W |
| PX0840/B/2M00 | CABLE PLUG IP68 USB B-A 2M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5042ETN+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5042EVKIT | 功能描述:电源管理IC开发工具 MAX5042 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX5043ATN+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5043ETN | 功能描述:开关变换器、稳压器与控制器 Two-Switch Power IC w/Power MOSFET RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX5043ETN+ | 功能描述:开关变换器、稳压器与控制器 Two-Switch Power IC w/Power MOSFET RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。