- 您现在的位置：买卖IC网 > PDF目录16545 > MAX5042ATN+T (Maxim Integrated Products)IC PWR W/MOSFET HS 56-TQFN PDF资料下载
参数资料
| 型号： | MAX5042ATN+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/22页 |
| 文件大小： | 0K |
| 描述： | IC PWR W/MOSFET HS 56-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 电源 |
| 电源电压： | 20 V ~ 76 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
| 包装： | 带卷 (TR) |
Two-Switch Power ICs with Integrated
Power MOSFETs and Hot-Swap Controller
C FLTINT ? FLTINT SH
I × t
1 . 4
where I FLTINT = 80μA,
t sh is the desired ignore time during which current-limit
events from the current-limit comparator are ignored.
Some testing may be required to fine tune the actual
value of the capacitor.
Calculate the approximate bleed resistance (R FLTINT )
needed for the desired recovery time using the follow-
ing formula:
Thermal Shutdown
The MAX5042/MAX5043 feature internal thermal shut-
down. Internal sensors monitor the high-power areas.
Thermal faults arise from excessive dissipation in the
power FETs or in the regulators. When the temperature
limit is reached, switching is terminated and the regulator
shuts down. The integration of thermal shutdown and the
power MOSFETs result in a very robust power circuit.
MAX5042 Hot-Swap Controller
The MAX5042 integrates a PWM power IC with a hot-
swap controller. The design allows a power supply built
around the MAX5042 to be safely hot-plugged into a
C FLTINT ln ?
?
R FLTINT ?
t RT
? 2 . 3 ?
? 1 . 6 ?
live backplane without causing a glitch on the power-
supply rail. The hot-swap section operates from
POSINHS to NEGIN. The MAX5042 only requires an
external N-channel MOSFET to provide hot-swap con-
where t RT is the desired recovery time.
Choose at least t RT = 10 x t SH . Typical values for t SH
range from a few hundred microseconds to a few mil-
liseconds.
Shutdown Modes
Latched Shutdown
The MAX5042/MAX5043 feature a latched shutdown that
terminates switching in the event of a serious fault.
External faults in synchronously rectified power supplies
cause a loss of control for the rectifiers. Either the body or
the external Schottky diodes conduct, resulting in a very
high power dissipation and a quick rise of the power-sup-
ply temperature. A thermal sensor placed on the same
ground plane as the secondary-side rectifiers can sense
this catastrophic increase in temperature and issue a
shutdown signal to PWMSD . Asserting PWMSD stops
switching and latches the fault until the power is cycled.
Connect PWMSD to REG5 to disable latched shutdown.
Functional Shutdown
Shut down the MAX5042/MAX5043 by pulling UVLO to
PWMNEG using an open-collector or open-drain transis-
tor connected to PWMNEG. Pulling HSEN to NEGIN also
shuts down the MAX5042 after a 10ms turn-off delay.
Pulling DEN low also shuts down the MAX5043 with a
1ms turn-off delay. When HSEN is used, the MAX5042
goes through a full hot-swap startup sequence with a
165ms startup delay. The MAX5043 also has a 10ms
delay from when DEN asserts.
trol. Figures 1 and 3 detail hot-swap functionality.
The MAX5042 controls an external N-channel power
MOSFET placed in the negative power-supply pathway.
When power is applied, the MAX5042 keeps the MOS-
FET off. The MOSFET remains off indefinitely if HSEN is
below 1.26V, POSINHS is below the undervoltage lock-
out level (31V), or the die temperature exceeds
+150°C. If none of these conditions exist for 165ms, the
MAX5042 gradually turns on the MOSFET, allowing the
voltage on HSDRAIN to fall no faster than 10V/ms.
During this period, the PWM block remains in shut-
down. The inrush current through the external MOSFET
(and therefore through the capacitor C IN ) is limited to a
level proportional to its capacitance, and the constant
HSDRAIN slew rate. After the MOSFET completely turns
on, and HSDRAIN falls to its final value, the hot-swap
period is terminated and the PWM section of the IC
powers up.
HSEN offers external control of the MAX5042, facilitat-
ing power-supply sequencing. HSEN can also be used
to change the undervoltage lockout level using an
external divider network, if necessary. Undervoltage
lockout keeps the external hot-swap MOSFET switched
off as long as the magnitude of the input voltage is
below the desired level. There is a 10ms turn-off delay
on the HSEN signal.
A power-good output, HSOK , asserts when the external
MOSFET completely turns on. HSOK is an open-drain
output referenced to NEGIN, and can withstand up to
80V above NEGIN.
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| PX0441/2M00 | CABLE IP68 MINI B TO A USB 2M |
| BA6219BFP-YE2 | IC DRIVER MOTOR REVERSE HSOP25 |
| VI-J5Y-EZ-S | CONVERTER MOD DC/DC 3.3V 16.5W |
| VI-J5W-EZ-S | CONVERTER MOD DC/DC 5.5V 25W |
| PX0840/B/2M00 | CABLE PLUG IP68 USB B-A 2M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5042ETN+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5042EVKIT | 功能描述:电源管理IC开发工具 MAX5042 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX5043ATN+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5043ETN | 功能描述:开关变换器、稳压器与控制器 Two-Switch Power IC w/Power MOSFET RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX5043ETN+ | 功能描述:开关变换器、稳压器与控制器 Two-Switch Power IC w/Power MOSFET RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。