参数资料
型号: MAX5066EVKIT
厂商: Maxim Integrated Products
文件页数: 12/22页
文件大小: 0K
描述: EVAL KIT FOR MAX5066
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
主要目的: DC/DC,步降
输出及类型: 2,非隔离
输出电压: 0.8V,1.3V
电流 - 输出: 10A,10A
输入电压: 5 ~ 16 V
稳压器拓扑结构: 降压
频率 - 开关: 500kHz
板类型: 完全填充
已供物品:
已用 IC / 零件: MAX5066
Configurable, Single-/Dual-Output, Synchronous
Buck Controller for High-Current Applications
Hiccup Fault Protection
The MAX5066 includes overload fault protection circuit-
ry that prevents damage to the power MOSFETs. The
fault protection consists of two digital fault integration
blocks that enable “hiccuping” under overcurrent con-
ditions. This circuit works as follows: for every clock
cycle the current-limit threshold is exceeded, the fault
integration counter increments by one count. Thus, if
the current-limit condition persists, then the counter
reaches its shutdown threshold in 32,768 counts and
shuts down the external MOSFETs. When the MAX5066
shuts down due to a fault, the counter begins to count
down, (since the current-limit condition has ended),
once every 16 clock cycles. Thus, the device counts
down for 524,288 clock cycles. At this point, switching
resumes. This produces an effective duty cycle of
6.25% power-up and 93.75% power-down under fault
conditions. With a switching frequency set to 250kHz,
power-up and power-down times are approximately
131ms and 2.09s, respectively.
Control Loop
The MAX5066 uses an average current-mode control
topology to regulate the output voltage. The control
loop consists of an inner current loop and an outer volt-
age loop. The inner current loop controls the output
current, while the outer voltage loop controls the output
voltage. The inner current loop absorbs the inductor
pole, reducing the order of the outer voltage loop to
that of a single-pole system. Figure 2 is the block dia-
gram of OUT1’s control loop.
The current loop consists of a current-sense resistor,
R SENSE , a current-sense amplifier (CA1), a current-
error amplifier (CEA1), an oscillator providing the carri-
er ramp, and a PWM comparator (CPWM1). The
precision current-sense amplifier (CA1) amplifies the
sense voltage across R SENSE by a factor of 36. The
inverting input to CEA1 senses the output of CA1. The
output of CEA1 is the difference between the voltage-
error amplifier output (EAOUT1) and the gained-up volt-
age from CA1. The RC compensation network
connected to CLP1 provides external frequency com-
pensation for the respective CEA1 (see the
Compensation section). The start of every clock cycle
enables the high-side driver and initiates a PWM on-
cycle. Comparator CPWM1 compares the output volt-
age from CEA1 against a 0 to 2V ramp from the
CSN1
CSP1
R CF
C CF
CA 1
CLP1
C CFF
V IN
R F
CEA1
CPWM1
DRIVE
I L
R SENSE
V OUT1
VEA1
2V P-P
C OUT
LOAD
R1
V REF = 0.61V
R2
Figure 2. Current and Voltage Loops
12
______________________________________________________________________________________
相关PDF资料
PDF描述
L-14C27NJV4T CER INDUCTOR 27NH 0603
MC33385VW IC SWITCH QUAD L-SIDE 20-HSOP
MC33186VW1 IC DRIVER H-BRIDGE 20-HSOP
ASEK712ELC-30A-T-DK BOARD EVAL FOR ASEK712ELC-30A
L-14C82NJV4T CER INDUCTOR 82NH 0603
相关代理商/技术参数
参数描述
MAX5067 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual-Phase, +0.6V to +3.3V Output Parallelable, Average-Current-Mode Controllers
MAX5067ETH 功能描述:电流型 PWM 控制器 Dual-Phase .6-3.3V Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5067ETH+ 功能描述:电流型 PWM 控制器 Dual-Phase .6-3.3V Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5067ETH+T 功能描述:电流型 PWM 控制器 Dual-Phase .6-3.3V Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5067ETH-T 功能描述:电流型 PWM 控制器 Dual-Phase .6-3.3V Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14