- 您现在的位置：买卖IC网 > PDF目录17280 > MAX5066EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX5066 PDF资料下载
参数资料
| 型号： | MAX5066EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/22页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX5066 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 0.8V，1.3V |
| 电流 - 输出： | 10A，10A |
| 输入电压： | 5 ~ 16 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 500kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX5066 |
Configurable, Single-/Dual-Output, Synchronous
Buck Controller for High-Current Applications
prevent shoot-through currents during transition. Figure 7
shows the dual-phase, single-output buck regulator.
inductor with a saturating current greater than the
worst-case peak inductor current:
Design Procedures
Inductor Selection
The switching frequency per phase, peak-to-peak ripple
I L _ PEAK =
24 . 75 × 10 ? 3
R SENSE
+
? I L
2
current in each phase, and allowable voltage ripple at
the output, determine the inductance value. Selecting
higher switching frequencies reduces the inductance
requirement, but at the cost of lower efficiency due to
the charge/discharge cycle of the gate and drain
capacitances in the switching MOSFETs. The situation
worsens at higher input voltages, since capacitive
switching losses are proportional to the square of the
input voltage. Lower switching frequencies on the other
hand will increase the peak-to-peak inductor ripple cur-
rent ( ? I L ) and therefore increase the MOSFET conduc-
tion losses (see the Power MOSFET Selection section for
a detailed description of MOSFET power loss).
When using higher inductor ripple current, the ripple
cancellation in the multiphase topology, reduces the
input and output capacitor RMS ripple current. Use the
following equation to determine the minimum induc-
tance value:
where 24.75mV is the maximum average current-limit
threshold for the current-sense amplifier and R SENSE is
the sense resistor.
Power MOSFET Selection
When choosing the MOSFETs, consider the total gate
charge, R DS(ON) , power dissipation, the maximum
drain-to-source voltage, and package thermal imped-
ance. The product of the MOSFET gate charge and on-
resistance is a figure of merit, with a lower number
signifying better performance. Choose MOSFETs opti-
mized for high-frequency switching applications. The
average gate-drive current from the MAX5066’s output
is proportional to the total capacitance it drives at DH1,
DH2, DL1, and DL2. The power dissipated in the
MAX5066 is proportional to the input voltage and the
average drive current. See the Supply Voltage
Connection (V IN /V REG ) and the Low-Side MOSFET
Drives Supply (V DD ) sections to determine the maxi-
mum total gate charge allowed from all driver outputs
L =
V OUT ( V IN ( MAX ) ? V OUT )
V IN × f SW × ? I L
together.
The losses may be broken into four categories: conduc-
Choose ? I L to be equal to about 30% of the output cur-
rent per channel. Since ? I L affects the output-ripple volt-
age, the inductance value may need minor adjustment
after choosing the output capacitors for full-rated efficien-
cy. Choose inductors from the standard high-current, sur-
face-mount inductor series available from various
manufacturers. Particular applications may require cus-
tom-made inductors. Use high-frequency core material
for custom inductors. High ? I L causes large peak-to-peak
flux excursion increasing the core losses at higher
frequencies. The high-frequency operation coupled with
high ? I L , reduces the required minimum inductance and
even makes the use of planar inductors possible. The
advantages of using planar magnetics include low-profile
design, excellent current sharing between phases due to
the tight control of parasitics, and low cost. For example,
the minimum inductance at V IN = 12V, V OUT = 0.8V, ? I L
= 3A, and f SW = 500kHz is 0.5μH.
The average current-mode control feature of the
MAX5066 limits the maximum inductor current, which
prevents the inductor from saturating. Choose an
tion loss, gate drive loss, switching loss and output loss.
The following simplified power loss equation is true for
both MOSFETs in the synchronous buck-converter:
P LOSS = P CONDUCTION + P GATEDRIVE + P SWITCH + P OUTPUT
For the low-side MOSFET, the P SWITCH term becomes
virtually zero because the body diode of the MOSFET is
conducting before the MOSFET is turned on.
Tables 1 and 2 describe the different losses and shows
an approximation of the losses during that period.
Input Capacitance
The discontinuous input-current waveform of the buck
converter causes large ripple currents in the input
capacitor. The switching frequency, peak inductor cur-
rent, and the allowable peak-to-peak voltage ripple
reflected back to the source, dictate the capacitance
requirement. Increasing the number of phases increas-
es the effective switching frequency and lowers the
peak-to-average current ratio, yielding lower input
capacitance requirement. It can be shown that the
______________________________________________________________________________________
17
相关PDF资料 |
PDF描述 |
|---|---|
| L-14C27NJV4T | CER INDUCTOR 27NH 0603 |
| MC33385VW | IC SWITCH QUAD L-SIDE 20-HSOP |
| MC33186VW1 | IC DRIVER H-BRIDGE 20-HSOP |
| ASEK712ELC-30A-T-DK | BOARD EVAL FOR ASEK712ELC-30A |
| L-14C82NJV4T | CER INDUCTOR 82NH 0603 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5067 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual-Phase, +0.6V to +3.3V Output Parallelable, Average-Current-Mode Controllers |
| MAX5067ETH | 功能描述:电流型 PWM 控制器 Dual-Phase .6-3.3V Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5067ETH+ | 功能描述:电流型 PWM 控制器 Dual-Phase .6-3.3V Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5067ETH+T | 功能描述:电流型 PWM 控制器 Dual-Phase .6-3.3V Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5067ETH-T | 功能描述:电流型 PWM 控制器 Dual-Phase .6-3.3V Parallelable Average RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。