- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6876ETX+ (Maxim Integrated Products)IC TRACKER/SUPERVISOR MON 36TQFN PDF资料下载
参数资料
| 型号： | MAX6876ETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/39页 |
| 文件大小： | 0K |
| 描述： | IC TRACKER/SUPERVISOR MON 36TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 序列发生器 |
| 监视电压数目： | 4 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
EEPROM-Programmable, Quad,
Power-Supply Tracker/Sequencer Circuit
Table 13. Program RESET
REGISTER
ADDRESS
EEPROM MEMORY
ADDRESS
BIT RANGE
DESCRIPTION
Bit 7 — If 1, OUT1 also controls RESET
If 0, OUT1 does not control RESET
Bit 6 — If 1, OUT2 also controls RESET
If 0, OUT2 does not control RESET
Bit 5 — If 1, OUT3 also controls RESET
If 0, OUT3 does not control RESET
11h
31h
[7:1]
Bit 4 — If 1, OUT4 also controls RESET
If 0, OUT4 does not control RESET
Bit [3:1] “ 000 ” reset timer value = 25μs
“ 001 ” reset timer value = 12.5ms
“ 010 ” reset timer value = 25.0ms
“ 011 ” reset timer value = 50.0ms
“ 100 ” reset timer value = 100.0ms
“ 101 ” reset timer value = 200.0ms
“ 110 ” reset timer value = 400.0ms
“ 111 ” reset timer value = 1600.0ms
SMBus/I 2 C-Compatible Serial Interface
The MAX6876 features an I 2 C/SMBus-compatible 2-
wire serial interface consisting of a serial data line
(SDA) and a serial clock line (SCL). SDA and SCL facili-
tate bidirectional communication between the
MAX6876 and the master device at clock rates up to
400kHz. Figure 10 shows the 2-wire interface timing
diagram. The MAX6876 is transmit/receive slave-only,
relying upon a master device to generate a clock sig-
nal. The master device (typically a microcontroller) initi-
ates a data transfer on the bus and generates SCL to
permit that transfer.
A master device communicates to the MAX6876 by
transmitting the proper address followed by command
and/or data words. Each transmit sequence is framed
by a START (S) or REPEATED START (SR) condition
and a STOP (P) condition. Each word transmitted over
the bus is 8 bits long and is always followed by an
acknowledge pulse.
SCL is a logic input, while SDA is an open-drain
input/output. SCL and SDA both require external pullup
resistors to generate the logic-high voltage. Use 4.7k ?
for most applications.
Bit Transfer
Each clock pulse transfers one data bit. The data on
SDA must remain stable while SCL is high (Figure 11);
otherwise, the MAX6876 registers a START or STOP
condition (Figure 12) from the master. SDA and SCL
idle high when the bus is not busy.
Start and Stop Conditions
Both SCL and SDA idle high when the bus is not busy.
A master device signals the beginning of a transmis-
sion with a START (S) condition (Figure 8) by transition-
ing SDA from high to low while SCL is high. The master
device issues a STOP (P) condition (Figure 8) by transi-
tioning SDA from low to high while SCL is high. A STOP
condition frees the bus for another transmission. The
bus remains active if a REPEATED START condition is
generated, such as in the block read protocol (see
Figure 11).
Early STOP Conditions
The MAX6876 recognizes a STOP condition at any point
during transmission except if a STOP condition occurs in
the same high pulse as a START condition. This condi-
tion is not a legal I 2 C format; at least one clock pulse
must separate any START and STOP condition.
______________________________________________________________________________________
25
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6879ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6881ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6884ETP+ | IC SUPERVISOR PWR SPL 20-TQFN |
| MAX6886ETP+T | IC SUPERVISOR HEX 20-TQFN |
| MAX6887RETE+ | IC SUPERVISOR HEX 16-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6876ETX+ | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876ETX+T | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876ETX-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876EVCMOD2 | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。