- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6876ETX+ (Maxim Integrated Products)IC TRACKER/SUPERVISOR MON 36TQFN PDF资料下载
参数资料
| 型号： | MAX6876ETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/39页 |
| 文件大小： | 0K |
| 描述： | IC TRACKER/SUPERVISOR MON 36TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 序列发生器 |
| 监视电压数目： | 4 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页
EEPROM-Programmable, Quad,
Power-Supply Tracker/Sequencer Circuit
Table 15. Configuration of Lock Bit
REGISTER
ADDRESS
13h
EEPROM MEMORY
ADDRESS
33h
BIT RANGE
2
DESCRIPTION
If 1, configuration registers are locked
If 0, configuration registers unlocked
6) The master generates a repeated start condition.
7) The master sends the 7-bit slave address and a
read bit (high).
8) The slave asserts an ACK on SDA.
9) The slave sends the 8-bit byte count (16).
10) The master asserts an ACK on SDA.
11) The slave sends 8 bits of data.
12) The master asserts an ACK on SDA.
13) Repeat steps 8 and 9 fifteen times.
14) The master generates a stop condition.
Address Pointers
Use the send byte protocol to set the register address
pointers before read and write operations. For the con-
figuration registers, valid address pointers range from
00h to 13h. Register addresses outside of this range
result in a NACK being issued from the MAX6876.
When using the block write protocol, the address point-
er automatically increments after each data byte,
except when the address pointer is already at 13h. If
the address pointer is already 13h, and more data
bytes are being sent, these subsequent bytes overwrite
address 13h repeatedly, leaving only the last data byte
sent stored at this register address.
For the configuration EEPROM, valid address pointers
range from 20h to 33h. When using the block write pro-
tocol, the address pointer automatically increments
after each data byte, except when the address pointer
is already at 33h. If the address pointer is already 33h,
and more data bytes are being sent, these subsequent
bytes overwrite address 33h repeatedly, leaving only
the last data byte sent stored at this register address.
Configuration EEPROM
The configuration EEPROM addresses range from 20h
to 33h. Write data to the configuration EEPROM to auto-
matically set up the MAX6876 upon power-up. Data
transfers from the configuration EEPROM to the config-
uration registers when ABP exceeds UVLO during
power-up. After ABP exceeds UVLO, an internal 1MHz
clock starts after a 5μs delay, and data transfer begins.
Data transfer disables access to the configuration reg-
isters and EEPROM. The data transfer from EEPROM to
the configuration registers takes 2ms (max). Read con-
figuration EEPROM data at any time after power-up or
software reboot. Write commands to the configuration
EEPROM are allowed at any time, unless the configura-
tion lock bit is set (see Table 15). The maximum cycle
time to write a single byte is 11ms (max).
Configuration Register Bank and EEPROM
The configuration registers can be directly modified
with the serial interface without modifying the EEPROM,
after the power-up procedure terminates and the con-
figuration EEPROM data has been loaded into the con-
figuration register bank. Use the write byte or block
write protocols to write directly to the configuration reg-
isters. Changes to the configuration registers are lost
upon power removal.
At device power-up, the register bank loads configura-
tion data from the EEPROM. Configuration data can be
directly altered in the register bank during application
development, allowing maximum flexibility. Transfer the
new configuration data byte-by-byte to the configura-
tion EEPROM with the write byte protocol. The next
device power-up or software reboot automatically loads
the new configuration (Table 16).
______________________________________________________________________________________
31
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6879ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6881ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6884ETP+ | IC SUPERVISOR PWR SPL 20-TQFN |
| MAX6886ETP+T | IC SUPERVISOR HEX 20-TQFN |
| MAX6887RETE+ | IC SUPERVISOR HEX 16-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6876ETX+ | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876ETX+T | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876ETX-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876EVCMOD2 | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。