- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6876ETX+ (Maxim Integrated Products)IC TRACKER/SUPERVISOR MON 36TQFN PDF资料下载
参数资料
| 型号： | MAX6876ETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 29/39页 |
| 文件大小： | 0K |
| 描述： | IC TRACKER/SUPERVISOR MON 36TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 序列发生器 |
| 监视电压数目： | 4 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
EEPROM-Programmable, Quad,
Power-Supply Tracker/Sequencer Circuit
SDA
1
0
1
0
A1
A0
X
R/W
ACK
START
MSB
LSB
SCL
Figure 14. Slave Address
8) The master sends a stop condition or sends another
8-bit data byte.
9) The addressed slave asserts an ACK on SDA.
10) The master sends a stop condition.
To write a single byte to the register bank, only the 8-bit
command code and a single 8-bit data byte are sent.
The command code must be in the range of 00h to 13h
to write on RAM or 20h to 33h to write on EEPROM. The
data byte is written to the register bank if the command
code is valid. The slave generates a NACK at step 5 if
the command code is invalid.
Block Write
The block write protocol allows the master device to
write a block of data (1 to 16 bytes) to the EEPROM or
to the register bank (see Figure 15). The destination
address must already be set by the send byte or write
byte protocol. If the number of bytes to be written caus-
es the address pointer to exceed 13h for the configura-
tion register (or 33h for the configuration EEPROM), the
address pointer stays at 13h (or 33h), overwriting this
memory address with the remaining bytes of data. The
last data byte sent is stored at register address 13h (or
33h). The block write procedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends the 8-bit command code for
block write (83h).
5) The addressed slave asserts an ACK on SDA.
6) The master sends the 8-bit byte count (1 to 16
bytes), N.
7) The addressed slave asserts an ACK on SDA.
8) The master sends 8 bits of data.
9) The addressed slave asserts an ACK on SDA.
10) Repeat steps 8 and 9 N - 1 times.
11) The master generates a stop condition.
Block Read
The block read protocol allows the master device to
read a block of 16 bytes from the EEPROM or register
bank (see Figure 15). Read fewer than 16 bytes of data
by issuing an early STOP condition from the master, or
by generating a NACK with the master. The send byte
or write byte protocol predetermines the destination
address with a command code of C1h. The block read
procedure follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave address and a
write bit (low).
3) The addressed slave asserts an ACK on SDA.
4) The master sends 8 bits of the block read com-
mand (C1h).
5) The slave asserts an ACK on SDA, unless busy.
______________________________________________________________________________________
29
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6879ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6881ETE+ | IC SEQUENCE/SUPERVISOR 16TQFN |
| MAX6884ETP+ | IC SUPERVISOR PWR SPL 20-TQFN |
| MAX6886ETP+T | IC SUPERVISOR HEX 20-TQFN |
| MAX6887RETE+ | IC SUPERVISOR HEX 16-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6876ETX+ | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876ETX+T | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876ETX-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876EVCMOD2 | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6876EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。