- 您现在的位置：买卖IC网 > PDF目录15858 > MAX6882ETE+ (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 16TQFN PDF资料下载
参数资料
| 型号： | MAX6882ETE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/19页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 16TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 类型： | 序列发生器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（4x4） |
| 包装： | 管件 |
Dual-/Triple-Voltage, Power-Supply
Sequencers/Supervisors
reference ramp voltage. During ramp down, if an OUT_
voltage is greater than the reference ramp voltage by
more than V TRK , the control loop dynamically stops the
control ramp voltage from decreasing until the slow
OUT_ voltage catches up. If an OUT_ voltage is greater
or less than the reference ramp voltage by more than
V TRK_F , a fault is signaled and the fast-shutdown mode
is initiated. In fast-shutdown mode, a 100 ? pulldown
resistor is connected from OUT_ to GND to quickly dis-
charge capacitance at OUT_, and GATE_ is pulled low
with a strong I GDS current (see Figure 3).
Figure 4 shows the aborted sequencing mode. When
EN/ UV goes low before t TIMEOUT expires, all the out-
puts go low, and the device goes into fast shutdown.
Internal Pulldown
To ensure that the OUT_ voltages are not held high by
a large output capacitance after a fault has occurred,
there is a 100 ? internal pulldown at OUT_. The pull-
down ensures that all OUT_ voltages are below V TH_PL
(referenced to GND) before power-up cycling is initiat-
ed. The internal pulldown also ensures a fast discharge
of the output capacitor during fast shutdown and fault
modes. The pulldowns are not present during normal
operation.
Stability Comment
No external compensation is required for sequencing
or slew-rate control.
Inputs
IN1/IN2/IN3
The highest voltage on IN1, IN2, or IN3 supplies power
to the device. The undervoltage threshold for each IN_
supply is set with an external resistor-divider from each
IN_ to SET_ to ground. To disable sequencing on any
IN_, connect IN_ to ground (or leave unconnected) and
connect SET_ to a voltage greater than 0.5V.
Undervoltage Lockout Threshold Inputs (SET_)
The MAX6880/MAX6881 feature three and the MAX6882/
Margin Input ( M A R G I N ) (MAX6880/MAX6882)
MARGIN allows system-level testing while power sup-
plies are below the normal ranges as adjusted by the
SET_ inputs. Drive MARGIN low before varying system
voltages below the adjusted thresholds to avoid signal-
ing an error. The state of PG/ RST does not change
while MARGIN is low. PG/ RST and all monitoring func-
tions are disabled while MARGIN is low. MARGIN
makes it possible to vary the supplies without a need to
adjust the thresholds to prevent sequencer alerts. Drive
MARGIN high or leave it unconnected for normal oper-
ating mode.
Slew-Rate Control Input (SLEW)
The reference ramp voltage slew rate during any con-
trolled power-up/down phase can be programmed in
the 90V/s to 950V/s range by connecting a capacitor
(C SLEW ) from SLEW to ground. Use the following for-
mula to calculate the typical slew rate:
Slew Rate = (9.35 x 10 -8 )/ C SLEW
where slew rate is in V/s and C SLEW is in farads.
The capacitor at C SLEW also sets the retry timeout peri-
od (t RETRY ), see Table 1.
For example, if C SLEW = 100pF, we have t RETRY =
350ms, t FAULT = 21.91ms, slew rate = 935V/s. For
example, if C SLEW = 1nF, we have t RETRY = 3.5s, slew
rate = 93.5V/s.
C SLEW is the capacitor on SLEW pad, and must be
large enough so the parasitic PC board capacitance is
negligible. C SLEW should be in the range of 100pF <
C SLEW < 1nF.
MAX6883 feature two externally adjustable IN_ under-
voltage lockout thresholds (SET1/SET2/SET3). The 0.5V
SET_ threshold enables monitoring IN_ voltages as low
V IN_
R1
IN_
MAX6880–
as 0.5V. The undervoltage threshold for each IN_ sup-
ply is set with an external resistor-divider from each IN_
to SET_ to ground (see Figure 6). All SET_ inputs must
be above the internal SET_ threshold (0.5V) to enable
sequencing functionality. Use the following formula to
set the UVLO threshold:
V IN_ = V TH (R1 + R2) / R2
where V IN_ is the undervoltage lockout threshold and
R2
SET_
MAX6883
V TH is the 500mV SET threshold.
Figure 6. Setting the Undervoltage (UVLO) Thresholds
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| CDRH8D43NP-220NC | INDUCTOR POWER 22UH 1.8A SMD |
| MAX6439UTAJYD3+T | IC BATTERY MON SNGL SOT23-6 |
| EBA22DRSN-S288 | CONN EDGECARD 44POS .125 EXTEND |
| MAX6439UTBITD3+T | IC BATTERY MON SNGL SOT23-6 |
| MAX6709FUB+ | IC VOLT MONITOR QUAD 10-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6882ETE+ | 功能描述:监控电路 Dual Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6882ETE+T | 功能描述:监控电路 Dual Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6882ETE-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6883ETE | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6883ETE+ | 功能描述:监控电路 Dual Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。