- 您现在的位置：买卖IC网 > PDF目录20169 > MAX753ESE+T (Maxim Integrated)IC CNTRLR CONTRAST 16-SOIC PDF资料下载
参数资料
| 型号： | MAX753ESE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR CONTRAST 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 显示器类型： | CCFL - 冷色阴极荧光灯 |
| 电流 - 电源： | 500µA |
| 电源电压： | 4 V ~ 30 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
CCFL Backlight and
LCD Contrast Controllers
Table 1. CCFL Circuit Component Descriptions (continued)
ITEM
C10
T1
DESCRIPTION
The ballast capacitor linearizes the CCFL impedance and guarantees no DC current through the lamp. 15pF
will work with just about any lamp. Depending on the lamp, you can try higher values, but this may cause the
regulation loop to become unstable. Larger values of C10 allow the circuit to operate with lower input volt-
ages. Don’t forget that C10 must be a high-voltage capacitor and cannot be polarized. A lamp with a
1500V RMS maximum strike voltage will require C10 to withstand 1500 x √ 2 = 2121V.
T1 must have high primary inductance (greater than 30μH), otherwise an inflated value of C9 will be required
in order to keep the Royer frequency below 60kHz (the maximum allowed by most lamps). A higher T1 sec-
ondary-to-primary turns ratio allows lower-voltage operation, but increases the size of the transformer.
You must select a value for C9 high enough to keep the lamp current reasonably sinusoidal and yet low
enough that T1’s core does not saturate. For the Sumida EPS207 with a 171:1 turns ratio, choose a 0.22μF
L MAG
value for C9. The characteristic impedance of the resonant tank equals
C 9
, where L MAG is the mag-
C9
R10
R5, R6
D6B, C7, R7
D6A, R17
L1
D5
C2
netizing inductance of T1. The characteristic impedance is defined as the ratio of the voltage across the par-
allel LC circuit divided by the current flowing between the inductor and capacitor. This circulating current is
not delivered to the load. If C9 has too large a value, it will cause excessive circulating currents, which will in
turn saturate the core of T1. It’s easy to tell when you have excess circulating current in the resonant tank,
because when you touch T1 you burn your finger. However, reducing the value of C9 decreases tank Q,
which increases the harmonic content of the lamp-current waveform. If the lamp-current waveform does not
look sinusoidal, then the circuit may not regulate to the right root mean square current.
R10 sets the base current for Q4 and Q5. If you choose too large a value for R10, Q4 and Q5 will overheat.
Too small a value will waste base current and slightly degrade efficiency. The optimal value will depend on
how much power you are trying to deliver to the lamp. 510 ? is a good “always works but may not be the most
efficient” value for use with the FMMT619 transistors from ZETEX.
This resistive divider senses the voltage at the center tap of T1. When the CC pin on the MAX758A rises
above 1.25V, the internal switch turns off, interrupting power to the Royer oscillator and limiting the open-lamp
transformer center-tap voltage.
D6B, C7, and R7 form a soft-start clamp, which limits the rate-of-rise of the peak current in the MAX758A.
Make sure R7 is at least 100k ? so it does not excessively load the CC pin.
D6A and R17 are also part of the soft-start clamp. The voltage on the SS pin controls the peak current in the
MAX758A’s switch. Make sure R17 is at least 100k ? so it does not excessively load the CC pin.
Inductor for the Switching-Current Source. Use a 47μH to 150μH inductor with a 1A to 1.5A saturation current.
Schottky Catch Diode. Use a 1A to 1.5A Schottky diode with low forward-voltage power.
Supply Bypass Capacitor. Use low-ESR capacitor.
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| PSA60R-240-R-CR1 | ADAPTER WALL R-SERIES 60W 24V |
| PSA60R-240-R-CNR3 | ADAPTER WALL R-SERIES 60W 24V |
| ACM31DRSN | CONN EDGECARD 62POS DIP .156 SLD |
| ABB11DHFD | CONN EDGECARD 22POS .050 SMD |
| FMM36DSEH | CONN EDGECARD 72POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX-754-1205AP | 功能描述:线性和开关式电源 MAX750 SERIES MULTI OUTPT PWR SUPPLY 12V RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
| MAX-754-1205G | 功能描述:PWR/PWR SUPPLY QUAD OUTPUT 750W RoHS:是 类别:电源 - 外部/内部（非板载） >> AC DC 转换器 系列:MAX-750 产品培训模块:MP Modular-Configurable AC-DC Power Supply 特色产品:Configurable Power Supplies 标准包装:1 系列:MP |
| MAX-754-1205P | 制造商:SLPOWER 制造商全称:SL Power Electronics 功能描述:MAX-750 Multiple Output |
| MAX-754-1252 | 制造商:SLPOWER 制造商全称:SL Power Electronics 功能描述:700, 750 WATTS MULTIPLE OUTPUT |
| MAX7545AKCWP | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。