- 您现在的位置：买卖IC网 > PDF目录1848 > MAX8655ETN+T (Maxim Integrated Products)IC REG BUCK ADJ 25A 56TQFN PDF资料下载
参数资料
| 型号： | MAX8655ETN+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/23页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 25A 56TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.7 V ~ 5.5 V |
| 输入电压： | 4.5 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 1MHz |
| 电流 - 输出： | 25A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
Highly Integrated, 25A, Wide-Input,
Internal MOSFET, Step-Down Regulator
Applications Information
PCB Layout Guidelines
Careful PCB layout is critical to achieve low losses and
clean, stable operation. Refer to the MAX8655
Evaluation Kit for an example layout. If it is necessary to
deviate from this layout, follow the procedure below.
Follow these guidelines for good PCB layout:
1) Place IC decoupling capacitors as close as possi-
ble to the IC pins. Separate the power and analog
ground planes. Place the input ceramic decoupling
capacitor directly across and as close as possible
to PVIN and PGND. This is to help contain the high
switching current within this small loop.
2) For output current greater than 10A, a four-layer
PCB is recommended. Pour an analog ground
4) Place the inductor current-sense resistor and
capacitor as close as possible to the inductor.
Make a Kelvin connection to minimize the effect of
PCB trace resistance. Place the input bias balance
resistor (R2 in Figure 8) near CS-. Run two closely
parallel traces from across capacitor C9 to CS+
and the input bias balance resistor R2.
5) Connect the exposed pad sections to the corre-
sponding IC pins and allow sufficient copper area
to help cooling the device.
6) Place the feedback and compensation components
as close as possible to the IC pins. Connect the
feedback resistor-divider from FB to V OUT as close
as possible to the farthest output capacitor.
plane in the second layer underneath the IC to mini-
mize noise coupling.
3) Connect input, output, and VL capacitors to the
power ground plane; connect all other capacitors to
the signal ground plane. Connect analog and
power ground planes at the output capacitor.
PROCESS: BiCMOS
Chip Information
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX865EUA | IC REG SWITCHD CAP DBL INV 8UMAX |
| MAX8660ETL/V+ | IC POWER MGMT XSCALE 48WQFN |
| MAX8663ETL+ | IC POWER MANAGE 40-TQFN-EP |
| MAX8664AEEP+T | IC CNTRLR DUAL OUT 20-QSOP |
| MAX8671XETL+T | IC PMIC W/CHARGER 40-TQFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8655EVKIT+ | 功能描述:电源管理IC开发工具 MAX8655/88 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8657 | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8658 | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8659 | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8659ETL+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。