- 您现在的位置：买卖IC网 > PDF目录1849 > MAX8744AETJ+T (Maxim Integrated Products)IC CNTRLR PWR SUP QUAD 32TQFN PDF资料下载
参数资料
| 型号： | MAX8744AETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/36页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR PWR SUP QUAD 32TQFN |
| 标准包装： | 2,500 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 6 V ~ 26 V |
| 输出数： | 4 |
| 输出电压： | 3.3V，5V，1 V ~ 26 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
Table 3. Operating Mode Truth Table
MODE
Shutdown Mode
Standby Mode
Normal Operation
3.3V SMPS Active
SHDN
Low
High
High
High
INPUTS*
ON5
X
Low
High
Low
ON3
X
Low
High
High
OFF
ON
ON
ON
LDO5
OFF
OFF
ON
OFF
OUTPUTS
5V SMPS
OFF
OFF
ON
ON
3V SMPS
OFF
5V SMPS Active
High
High
Low
LDO5 to CSL5 bypass
ON
OFF
switch enabled
Normal Operation
OFF
ON
(Delayed 5V SMPS
High
Ref
High
LDO5 to CSL5 bypass
Power-up after 3.3V
ON
Startup)
Normal Operation
switch enabled
OFF
SMPS is in regulation
ON
(Delayed 3.3V SMPS
High
High
Ref
LDO5 to CSL5 bypass
ON
Power-up after 5V
Startup)
switch enabled
SMPS is in regulation
* SHDN is an accurate, low-voltage logic input with 1V falling-edge threshold voltage and 1.6V rising-edge threshold voltage. ON3
and ON5 are tri-level CMOS logic inputs, a logic-low voltage is less than 0.8V, a logic-high voltage is greater than 2.4V, and the mid-
dle-logic level is between 1.7V and 2.3V (see the Electrical Characteristics table).
The LDO5 input undervoltage-lockout (UVLO) circuitry
inhibits switching if the 5V bias supply (LDO5) is below
its 4V UVLO threshold. Once the 5V bias supply
(LDO5) rises above this input UVLO threshold and the
SMPS controllers are enabled (ON_ driven high), the
SMPS controllers start switching, and the output volt-
ages begin to ramp up using soft-start. If the LDO5
voltage drops below the UVLO threshold, the controller
stops switching and pulls the low-side gate drivers low
until the LDO5 voltage recovers or drops below the
POR threshold.
The internal soft-start gradually increases the feedback
voltage with a 1V/ms slew rate. Therefore, the outputs
reach their nominal regulation voltage 2ms after the
SMPS controllers are enabled (see the Soft-Start
Waveform in the Typical Operating Characteristics).
This gradual slew rate effectively reduces the input
surge current by minimizing the current required to
charge the output capacitors (I OUT = I LOAD + C OUT x
V OUT(NOM) /t SLEW ).
SMPS Enable Controls (ON3, ON5)
ON3 and ON5 control SMPS power-up sequencing.
ON3 or ON5 rising above 2.4V enables the respective
outputs. ON3 or ON5 falling below 1.6V disables the
respective outputs. Driving ON_ below 0.8V clears the
overvoltage, undervoltage, and thermal fault latches.
SMPS Power-Up Sequencing
Connecting ON3 or ON5 to REF forces the respective
outputs off while the other output is below regulation
and starts after that output regulates. The second
SMPS remains on until the first SMPS turns off, the
device shuts down, a fault occurs, or LDO5 goes into
UVLO. Both supplies begin their power-down
sequence immediately when the first supply turns off.
Output Discharge (Soft-Shutdown)
When the switching regulators are disabled—when ON_
or SHDN is pulled low, or when an output undervoltage
fault occurs —the internal soft-shutdown gradually
decreases the feedback voltage with a 0.5V/ms slew rate.
Therefore, the regulation voltage drops to 0V within 4ms
after the SMPS controllers are disabled (see the SMPS
Shutdown Waveform in the Typical Operating
Characteristics ). This slowly discharges the output
capacitance, eliminating the negative output voltages
caused by quickly discharging the output through the
inductor and low-side MOSFET. When an SMPS target
voltage discharges to 0.1V, its low-side driver (DL_) is
forced high, clamping the respective SMPS output to
GND. The reference remains active to provide an accu-
rate threshold and to provide overvoltage protection. Both
SMPS controllers contain separate soft-shutdown circuits.
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8745ETJ+ | IC CNTRLR PWR SUP QUAD 32TQFN |
| MAX8751ETJ+T | IC CNTRLR CCFL INV 32-TQFN |
| MAX8752ETA+T | IC DC-DC CONV TFT LCD 8-TDFN |
| MAX8753ETI+T | IC DC-DC CONV TFT LCD 28TQFN |
| MAX8756ETI+T | IC CNTRL DUAL PS 28-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8744AEVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX8744A EVAL KIT - Rail/Tube |
| MAX8744ETJ+ | 功能描述:电流型 PWM 控制器 Quad-Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX8744ETJ+T | 功能描述:电流和电力监控器、调节器 Quad-Out Main Power Supply Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX8744EVKIT | 制造商:Maxim Integrated Products 功能描述:HIGH-EFFICIENCY QUAD OUTPUT MAIN - Rail/Tube |
| MAX8744EVKIT+ | 制造商:Maxim Integrated Products 功能描述:HIGH-EFFICIENCY QUAD OUTPUT MAIN - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。